Search results

Is anyone running a pedestal launcher in their cockpit of their 272 Sailfish? If so, can you share your pictures and experience with how it interferes with space? I am considering it for offshore trips but, concerned about how much space it takes up.

I have a 1995 272 Sailfish and I can't stand the wasted space in the helm to side of each seat. Has anyone done anything unique with this area? I was thinking of taking the boat to a fairly local Starboard fabricator this coming offseason and have him remove the shelf/trim and enclose the whole...

While repowering my 272 Sailfish I broke the plastic recessed mount for the remote oil fill cap. I emailed Grady and didn't get much help. Does anyone know what the proper name is and where I might be able to get them? I would really like to replace it before I put my livewell back in. Thanks

I have 1995 272 Sailfish and I have been replacing all of the thru hulls. I ordered the thru hull fittings according to GW specs but, the one sent for the deck drain scuppers don't have the pre-drilled areas to attach the plastic scupper ring. My question; are the scuppers REALLY necessary or do...

While rigging new to me motors on my 1995 272 Sailfish I will be replacing all of the thru hull drains. I have a parts list from GW but, they use various Attwood and Perko parts. I am having problems finding one place that has all of the drains that I need. Has anyone had any luck sourcing all...

Does anyone know where to get the oil fill "wells" (holds the cap/inlet) for a 272 Sailfish. I know I can contact Grady but, was hoping for an aftermarket source. I cracked mine installing new outboards.

I am looking at redoing the switch panel on my 272 Sailfish this winter. My question for those of you who have done this; Did you remove your circuit breakers and replace them with an add-on fuse block? By doing so seems like a great way to save some money and clean up the panel. Thoughts on...

Does anyone know the size of this broken thru hull above the water line? I think it would be 3/4 but, not sure what the barb size would be. Boat is some distance away from me right now. I believe this is the overboard drain for the shower sump/forward bilge.

Does anyone know what size and length of motor rigging tubes are needed on a 272 sailfish? I'd like to replace mine when repowering next week.

Does anyone know offhand the lengths of shift cable needed on a 1995 272 Sailfish? I cannot see the markings on mine and will be replacing them during a repower. I don't want to wait until I remove them to measure.

I will be repowering in a week or two. While doing so I am going to replace all of my fuel lines. Does anyone have a rough idea of how many total feet is needed for twins? I will be ordering it at dealer cost but, it is expensive and I don't need extra lying around. Thanks

Hey, guys. I am running a 1995 272 Sailfish which I am putting on 2007 225 ETEC's soon. A friend of mine works for a company that is a Garmin dealer so, I should be able to buy with a 20%-25% discount. I am running Garmin electronics so, I'd like to stick with them anyway. Can anyone tell me...

Sea trial of "new" motors went well. Deposit made. Should be bringing home 225 Etec's the week of the 30th. I just may make striper and tog season! For those of you with 272 Sailfish with gen 1 etecs; what kind of fuel burn are you seeing and with what props?

Sea trial of "new" motors went well. Deposit made. Should be bringing home 225 Etec's the week of the 30th. I just may make striper and tog season! For those of you with 272 Sailfish with gen 1 etecs; what kind of fuel burn are you seeing and with what props?

Anyone running Mercury EFI's on their Grady? Opinions? Specifically 272 Sailfish....

Are any of you running a 1995'ish 272 sailfish with 4 strokes? What kind of fuel efficiency numbers are you seeing? Were you close to sinking your scuppers?

I want to replace my fuel sending units on my 1995 272 Sailfish. I am not near the boat to measure the tank/units but, called Grady. I was told I need a 17" sender for the main and 16" for the aux tank. Can anyone confirm this? I have seen a bunch of posts where people used 16" units. I don't...

Has anyone had their original fishbox and livewell lids replaced with starboard? A friend of mine owns a holster company and has a CNC machine. I was going to check

Are any of you running 30" motors on a 5" step plate, particularly on an older 272 Sailfish? I am entertaining getting newer to me motors but, the best pair I have found are 30". I have been told I can install a 5" step jack plate and it would work. Does anyone have firsthand knowledge? Thanks!

Hello all. I am currently running twin 1995 200 Johnson's on my 1995 272 Sailfish. The motors run strong but, are very old and not very fuel efficient. There is a guy local to me who has twin 2001 Yamaha 200 HDPI's that are on a 26 Regulator that he bought with the intent to repower with 4...