Search results

Has anyone purchased replacement hull logos lately? I know Grady is not making the blue/gold one anymore and is now blue/chrome. Has anyone purchased an aftermarket version of either? There used to be a vendor on eBay that had decent ones but they are not there anymore. I saw blue/chrome ones...

Going to swap out the deck drains/hoses on my 2004 Journey . Where are you buying and what brand is everyone buying ? I see the ones on eBay that say they are the new style Grady for 80$ each (nylon with stainless cover) but think id rather go with all stainless. Thanks for the help!

Somehow got water in the courtesy light/spreader light switch on my 258 Journey(under hard top). The courtesy light still works but spreader lights do not. Is there a fuse/breaker for the spreader or is the switch doa? Spreader lights are new and worked all season up until now. Thanks!

Need to replace the brass drain tubes in the splash well on my 2004 Journey 258. Does anyone know what diameter I need?? Called grady but they are closed for the holiday. Thanks!

Looking for ideas to install a small removeable table in the cabin. Im leaning towards a base installed in floor with removable post and table but wanted to see what others have done. Thanks!

I'm planning on compound and waxing my boat this week. Have an older 6" polisher that runs at either 1250 or 1500 rpm. Looking at the newer polishers on the market they go up to 5-6K rpm. Am i good with what I have or should i look into upgrading to a more powerful polisher? Thanks!

Recently purchased a 2004 258 a few hours away from me. Looking to buy a trailer and forgot to take bow eye to transom measurement when i was there. Anyone have it ? Thanks!

Has anyone installed a windlass i On the 225 with a factory pulpit? Have a lewmar 700 im installing and dont think ill get enough drop in the anchor locker if mounted on pulpit but really dont want to mount on anchor locker hatch. Any help appreciated

Im adding underwater lights to my tournament 225. I Need to find a spot to install a switch. On the top row of the switch panel is 4 "acc" circles (see attached pic). Is there a switch I can buy that will fit in one of those spots? Are those breakers for something else? Probably a dumb question...

Looking to find a winter cover for my 97 tournament 225g with a provision for the bow pulpit. Trying to find one made specifically for this model and not just a off the shelf cover. Anyone know a company that sells them? Thanks

Have a 1997 Tournament 225G. Need to replace the sliding seat mount for the ladder back helm chair. Does anyone know off hand the diameter of the seat post. Is it 2 3/8" or 2 7/8"? I believe the seat is Wise so Ill probably order that seat mount or does anyone suggest a different vendor? Would...

Have a 1997 yamaha 225 on my Tournament. Engine starts and runs no issue. Took it out yesterday and engine would only go up to 2800 rpm when i gave it full throttle, then about 15-20 seconds later it would surge to normal rpms on its own and run perfect. If i backed the throttle down to below...

Looking to replace the beaten up rod holder rack under the livewell on my tournament. Anyone know where i can find a nice stainless one that can use or cover the holes where the existing one is mounted? Thanks!

Have a 1997 Tournament with the 100 gallon main and 50 gallon aux fuel tanks. Have had gas smell and traces of fuel in bilge. Replaced the gaskets on both the fuel sender units(aux one was shot). Everything I can see from access ports looks clean and tanks appear to be clean from the top with...

Just replace the 2 lights under the port and starboard console with lumitec mirage 3 color led. Looking to add more lights to light up the back deck more. Guessing get strip lights and mount under gunwale on each side? What are others using ? Thanks!

Have a Tournament 225 with the outboard on the factory bracket. Looking to install the Lowrance active scan 3in1 transom mount transducer. Is there anything different when installing a transom mount transucer with the outboard being set back on the bracket? Most sites say at least 15" from side...

I recently purchased a 1997 Tournament 225g with the engine bracket. Im located in NY saltwater and it will be in slip for the season and would like to use ablative bottom paint with copper since Ive had great luck with it before on other boats. This is the first boat I have had with a aluminum...