Search results

Anyone know where I could find a few of these clips?

Anyone know how the rear seatback on a '95 Islander is installed? Is it the same as the bolsters? See Pics.

Will a 25" shaft '95 Johnson 175 fit on a '75 204C?

I am in the process of replacing the Twin '95 175 Johnsons w/ '05 Evinrude 175's. Question on the wiring of the Battery Isolator. I failed to take note of how the Isolator was connected. There are 4 wires going to the Isolator as illustrated in the attachment, but I'm not sure on where they were...

Looked at my scupper hoses tonight and confirmed my suspicions that they need replacing. Any recommendations for scuppers and where to purchase? Stainless, bronze, plastic, etc....???

I have a '95 268 Islander w/ twin '95 Johnson 175's. They weigh ~375# ea, boat is rated for 400HP Max. Considering a pair us '99 Yamaha ox66 225's. They weigh ~500# ea.......that's an additional 250lbs hanging off the back, no too worried about the additional 50HP.....never ride WOT. The '95 200...

Think I have a bad sending unit for the aux fuel tank on my Islander. I have the fresh water tank and it seems as though the aux fuel tank is under the fresh water tank. There's an access port at the stern of the hatch at the helm deck........if that makes sense. There's another access port at...

Finally getting around to getting the fresh water system on my Islander operational. Added water to the fresh water tank........hit the water pressure switch.......opened the faucet in the cabin sink and water started to come out, closed that faucet and opened the faucet in the head, no water...

Need to replace some of the stripe on my '95 Islander. Any ideas on where to score some? Have seen it on ebay at times.......not at the moment.

What is the difference? Are they interchangeable? Deck hatch vs. below waterline through hull opening for transducer install (~1" hole).

Need to replace a transducer on my '95 268 Islander which has the stepped hull. Currently the transducer is mounted on the "vertical" surface which is approximately 24" fwd of the transom. In this configuration the cable for the transducer goes through the hull below the water line. Whoever...

Removed the hatches from my '95 268 Islander. Just purchased July '19. Hatch over the main tank had already been recored but the smaller rear one needed re-coring. Found rubber strips around the edges, see pics. Was this from Grady or the PO? There wasn't and caulking installed either.......

I have a new to me '95 Islander. During the off season I am getting more familiar w/ the boats systems. Has a raw water pump contected the washdown hose and the "live well". The raw water enters the hull and goes to a valve which is connected to a "T". One side of the "T" goes to the Pump and...

Recently purchased a '95 Islander 268. Basically just enjoyed using the boat last season, purchased in July. Getting familiar with the fresh water system.....do not see a pump at the bottom of the tank, found a orange and black wire near the fresh water tank not connected to anything, found the...

Recently purchased a '95 268 Islander w/ Twin '95 Johnson 175's. VERY pleased with the boat so far having upgraded from a 241 Offshore. The islander has a 2-step swim ladder that sits in a molded section of the euro transom. Does anyone know if a 3-step ladder is available that will still fit...

Recently purchased the subject boat. i am very hsppy with it. I do have some getting used to though in comparison to my Offshore. The Islander seems to porpoise a bit. Have the twin 175's trimmed down a bit. Only using tabs for side to side adjustment at the moment. Any suggestions?

Any suggestions other than Grady on where to get owners manuals?

Just bought a '95 268 Islander w/ twin '95 Johnson 175's. Wasn't able to perform a sea trial, did compression test Port engine ranged from 80 to 95; Sbd engine ranged from 95 to 115. Need to know the weight with or without the engines. The brochure says 4660 w/o the engines. Have gotten...

Any 1st hand experience w/ subject package? Any performance numbers available? I have gotten somewhat comfortable w/ the I/O's........they're ALOT less $$$ to repair or replace, and I can work on them myself. Any/all info is welcome.

Anyone have 1st hand experience w/ a 254 Sailfish w/ a 7.4L Mercruiser I/O? I currently have a '84 241 Offshore w/ a Vortec SBC.......a bit concerned about the 254 being under powered! Any/all info welcome.