Hookup1's latest activity

  • Hookup1
    Hookup1 replied to the thread Top & Windshield Upgrade.
    I have a one piece polycarbonate front. It does get warm even without the sides and vent windows open. I like the idea or venting the...
  • Hookup1
    Try to get behind it to install new screws with washers and nuts. You could also go to a larger oval hard screw with finish washers...
  • Hookup1
    Hookup1 replied to the thread 226 Seafarer anchor light wire.
    Difficult to splice or impossible to splice? There is a difference. How about a pic? I doubt you will find a "trick" way to replace...
  • Hookup1
    Hookup1 replied to the thread 226 Seafarer anchor light wire.
    If the wire is not broken and you have a little of it exposed spllce, solder and shrink a new wire on. Crimps are too bulky. My best...
  • Hookup1
    Hookup1 replied to the thread rain water 265 express.
    Water could be coming from anywhere on the boat. GW has a 1/2" PVC pipe imbedded in the hull that runs from the forward bilge to the...
    • 268 tubing layout.jpeg
    • Aft bilge 268.jpeg
    • 27 Bulkhead 1.jpeg
    • 23b Plug.jpeg
  • Hookup1
    Hookup1 replied to the thread Pilot seat base repair.
    Pictures are always helpful. I have no idea what your boat looks like, where this is happening and what is underneath. My seat slide...
  • Hookup1
    Hookup1 replied to the thread Macerator not pumping in GS 232.
    I haver always had problems with these pumps lifting. They quote: Jabsco macerator pumps are capable of self-priming and lifting waste...
  • Hookup1
    Hookup1 replied to the thread Hardtop fiberglass repair.
    I refinished my hardtop a few years ago. Gelcoat chipping all around and heavy chalking. Also no reinforcement for the rigger bases...
    • Repair underside.jpeg
    • Hardtop underside.jpeg
    • Hardtop underside 2.jpeg
    • Hardtop top 2.jpeg
    • Hardtop top 1.jpeg
    • Hardtop on.jpeg
    • Hardtop coring.jpeg
    • Gel fail.jpeg
    • Gel Chips.jpeg
  • Hookup1
    Hookup1 replied to the thread Macerator not pumping in GS 232.
    Put a picture or two up of your tank and macerator. What is the manufacturer and model of the macerator. Older GW used a in-tank Groco...
    • Macerator 1.jpg
  • Hookup1
    How about a photo of the latch. Not sure if its different than mine.
  • Hookup1
    Hookup1 replied to the thread Dual gas input issues.
    Be careful pulling the sending unit. If the tank is full you will have fuel all over the place.
  • Hookup1
    Hookup1 replied to the thread 20 year old varnish in tank 208.
    It's not varnish. It's discolored water. And you probably still have more in the tank. You won't get it out unless you shake up the...
  • Hookup1
    Hookup1 replied to the thread Electrical Issue-Long Shot.
    Are there no wires running to the hardtop anymore? When I pulled my tower and hardtop to refinish I pulled the wires back and when...
  • Hookup1
    Hookup1 replied to the thread Replacement Wood and Clear Cover.
    Clear covers are acrylic plastic. The teak trim is probably not real wood. Some kind of fake teak plastic - at that is what's on mine...
    • Finished Switch.jpeg
    • Finished Gauge.jpeg
    • 8612 and panel.jpeg
    • 8610 Overhead Box.jpeg
  • Hookup1
    Hookup1 replied to the thread Fishy responses to want add?.
    First off it's highly unlikely this will work out. Could be legitimate but you have to be careful. So many frauds online. Where is the...