Search results

  1. N

    LED cabin lighting and under water stern lights

    MB electronics, they are at THT.
  2. N

    1986 Seafarer 227: 5/6/14 Update - Stringer extension prep

    Re: 1986 Seafarer 227 Not-A-Project: 2/24/13 Update Nice work, keep going man.
  3. N

    First time bottom paint question

    When you sand the ablative paint to apply the new one, if you don't have the hard under it you will be sanding the barrier coat, besides gives the extra protection and you only do it once(the hard).
  4. N

    First time bottom paint question

    Epoxy barrier coat is a must, especially if the boats lives in warm waters. Three coats is the way to go, then two coats of hard bottom paint(let's say blue color) then one or two coats of ablative bottom paint(let's say black color). When you see blue color you should touch up that spot with...
  5. N

    offshore running with air condition on ???

    Your generator impeller is ready to go.
  6. N

    Bad battery or wiring?

    Sounds like a bad ground bridge cable, most likely bad or loose connector on the "bad" battery side.
  7. N

    Hard top rod holders on canyon 366?

    Knew that but didn't want to say anything.
  8. N

    232 Gulfstream Switch Panel Question

    I can't really tell from your picture but i can see the last switch on the first row is to switch the reading on your tanks to the gauge which does not require a hot wire so no breaker. What are the other switches for?
  9. N

    T-top Crab puller question

    John Carroll Winterville Machine Works 252-756-2130 Call this person. He is the one that made your top.
  10. N

    Grady 282 Upgrades

    Check these guys out, looks like a good product without the real teak maintenance. http://www.plasteak.com/
  11. N

    Adding Tower to 330 Express

    I just Googled images for "Grady White with tower" and a whole bunch showed up. Some really nice ones too.
  12. N

    Thinking of getting a Honda EU2000i

    The safest place i would think is outside the transom and make sure no wind is blowing towards the cabin. As far as the cable, you can rig one with a male 15 or 20 AMP plug to connect to the Honda and a female round 20 AMP or what ever you have now for the boat side. That is the safest way to do...
  13. N

    1986 GW Sailfish 255

    I used Meranti BS1088 which is true marine plywood and bought it from Roberts Plywood for 75 for 1/2" and 90 for 3/4". If you do cut the transom from the outside(back) then you might need couple of more gallons epoxy because you have to built up with 1708 the exterior layer to like 1/4" which is...
  14. N

    1986 GW Sailfish 255

    Materials you need to do your transom is: 10 yards of 1708 glass.............................90.00 5 gallons of epoxy resin...........................250.00 3 sheets of 3/4 plywood or 3/4 coosa...........300.00 or 600.00 5 lbs woodflour.....................................20.00 1 lb...
  15. N

    "Sonar" vs FishFinder: What's the Difference

    A fishfinder IS a sonar, so yes, the same thing.
  16. N

    How to get DVD player out of marlin

    Got any pictures? Where is it located?
  17. N

    New to me Grady 228G

    She looks great, congrats and good luck.
  18. N

    Poor Customer Service from Grady White

    Poor customer service ? Are you kidding ? You got free gel cote too. Let me remind you your boat is 11 years old.
  19. N

    Hope she floats - 192 tournament

    Congrats on the new boat. As far as the seacock, LOOK for it, it has to be somewhere close to the livewell.
  20. N

    Underwater Lights 330 Express

    You don't even have to install the wire with a screw, just duct tape it in place in a few spots and then run a thin bid of 5200 on each side of the wire in 3-4 places, that will stay there for ever. I did it like that on the skiff because it has coosa transom and it was above water line. I had...