Search results

Well Guys,I found some ..Industrial Hardware Direct..Supposed to be Direct replacements for the ones I have...$20.00 Each.....Yes they are Stainless....BUT....Didn't think about it when I ordered them....They ARE Made in China! Didn't indicate that in the Book.. Should have known by the...

Dave,I have a 226 with the Livewell on the Port side.Are You talking about the Rear Live Well?

Thanks Guys,Always a wealth of knowledge! Have to say after owning My 2005 226 Seafaerer for almost 2 yr's now...I really like it! Not another 22-23 W/A as well thought out and spacious [Deck wise] made.I've tweaked Engine Height and Prop.And learned how to Run the Boat.It took some adjusting on...

Kinda figured the "GW" was a Grady part number...Didn't know about the phone # though...Has anyone found the equivalent Stainless ones or what pound opened strength they are? I take it Vero Marine will ship? Thanks!!!

Need a new Gas Strut for my Livewell lid.Made by Ameritool. Has numbers...315/668/2172.....and....GW# 10-296.It is 11" extended and I don't see any #'s for the amount of extend pressure.Anyone know where to get these??? Thanks!!

Welcome K.d. What part of S.C.? Wife has some Relatives on Wadmalaw,Johns,James Islands and Charleston.

Was hoping someone knew the exact ones that came on them.

Just getting around to this...Anyone have the correct part number for these? I'm getting confused looking at them,Different degrees of opening,,,C-6,etc....Thanks!

Don't know if it will help ya',But on my 2005 Seafarer they mounted it in the right under Bunk storage compartment in the Cabin.

May be coming in thru the Hull and Cap Joints..Take a Hose and squirt water all around,underneath the Rub Rail..

Exactly! Thanks!!!!

Guys,I need to replace the Spring Hinges on my 226 Seafarer.The ones that hold the Clear Door up on the Electronics Box..Where can I get these? I swear I just read about someone getting them,but for the Life of me can't remember what post it was on!

Having the same problem on my 2005 Grady ! Bought it about 18 months ago and have put 160 hrs. on it. Is yours the same switch/side all the time? I've been thru 3 switches already and everything seems to be fine with the system. I do need to do a current draw test though.

I have always had Roller Trailers.That being said,I've always had an Electric Winch! If the Trailer is set-up properly for the Hull,Loading should be a Breeze.The Boat should center itself on the Rollers.NO way I'm Hand Winching my Boat,That's enough to make ya' get rid of a Roller Trailer in...

I have a 2005 226 with a Hard Top,Full Enclosure with a F-225.Have a 17" Rev-4,Engine mounted all the way up. I've gotten 43.5 mph. out of it on a good day..I will say the Engine probably needs to come down a Hole though. Still would like to have a 300 on it! :twisted: I'd like to be able to...

300H.P.!! :mrgreen: I know the newer 226/228's will take up to a 300 now. Have they done any structural upgrades for the higher h.p. Engines?

Have to disagree with the 2002-2004 time frame and Yamaha Taking care of it in 2005. Have a 2005 F-225 ..185 hrs. and it was starting! Have seen 2006's also,along with some F-150's !

Cool looking Hard Top !! Custom made?

Sweet!!! Don't get any better than that! I'm in the crappy N.East..I don't care for the cold weather anymore.

I went with the 12x12's so I didn't have to re-drill for wider Tabs.For the most part most manufactuers don't put enough Tab on their Boats.They need to work without having to Dig them in.Lowest Planing speed? Don't know,haven't really tried to figure it out.Most efficient cruise,Don't know that...