Search results

“Debond Comapny, Marine Formula” https://marineformula.com/

If it does have a drain hole, or enough room to drill a hole through the bottom, you could improvise similar to a gear puller with a 6” bolt, a few washers and a spanner. Spanner could be made of wood with a hole for the bolt. Bolt and big washer underneath,spanner above, tighten nut from up...

Tap it out from underneath after running a razor knife around the top lip. It likely has a drain line under there too.

I ordered twin helm chairs instead of the normal port side lounge set up. The seats themselves have bolsters. The pedestals have adjustment forward/back and height. The height adjustment comes in handy when there’s a passenger seated in the bow in front of the helm. Edit: the pedestal is made...

I found a 12” ecomap at Bass Pro on sale for my current boat that included a GT54. May want to check their sales. The ClearVu and SideVu features are pretty cool bit the echo series are suited for shallow waters. I think it’s 350 watts which should reach 200’ depth, maybe, but suited my needs. I...

Welcome and thank you for your service! Just south of you in Charleston and looking forward to following your project. Cool boat!

As many have said, drill pilot hole then chamfer depth beyond gel coat thickness. As to the cover itself and assuming you’re working with Sunbrella, I use a pencil soldering iron to make the snap hole in the fabric. It sears the threads together similar to the end of a docking line.

i think the switch lights are LED and maybe serviceable, but I’ve just bought new switch bodies. There are a variety of bodies depending on function so have a look as to the type before ordering. When replacing, I take a phone pic of how the switch is wired prior to pulling any wires off. As...

Thanks for the pics! That’s a beautiful boat. I’m sure you’re stoked! that sticker on the port gunwale at the transom is the factory QC sticker. It has the initials of the inspectors. It peels off easy. I stuck it on a sheet of paper and kept it.

I posted in another thread in General Discussion of a dash I remodeled on a Freedom 225. I had New Wire make the new dash panel. The hole I cut in the dash followed the outside edge of the new panel minus roughly 1/2”, so within reason and very important to minimize work extended wiring, cables...

congrats! need some pics

You may want to consider a new dash panel. This is a dash from a Freedom 225 that I ordered a custom panel from New Wire Marine. All the cut outs were done by them In a carbon fiber substrate. The toggle switches/breakers didn’t need to be rewired once the factory zip ties were cut as there was...

You should find small white plastic “grommets“ with a ~1/4” hole in them, usually on a vertical surface adjacent to the cockpit floor underneath cupholders. tI’ve only really seen a need for the drains when I wash the boat. make sure the helm console cupholders are plumbed so they don’t spill...

Congrats and welcome!

Uneducated guess…the nut was over tightened when installed and the threads are galled. Stainless is relatively soft. Since it’s already at a machine shop, cut the nut off and rethread the shaft on a lathe. It would end up an inch or two shorter but as long as it clears the motor cowling should...

Are you measuring the 11.5v when you’re actively starting the engine(s)? If so, the voltage drop when starting may be normal. Are there any other symptoms of weak batteries, like electronics shutting down?

Cockpit Floor to top of gunwale

Is there a ramp convenien? If so, take a few tools to loosen the winch stand bolts. After getting to the ramp, move winch stand to desired position, retighten bolts, leaving winch strap connected. Back trailer down until boat floats, winch up to new position. Make sure to do on a busy Saturday...

Marinco makes a bulkhead fitting for plugging in an extension cord. I installed one recently to power a dual bank NOCO Genius charger.

Maybe check Taylor Made. They are the factory vendor for my bow and cockpit covers, Bimini, Bimini dodger and side curtains. They’re also the vendor for the windshield on my 24 Freedom 215.