Search results

... half the price amazon countersink tool

I'd find the correct size washer and DIY it using a tool like this: Countersink tool I would def not pay 50 bucks for it but im sure a cheaper substitute could be found. Once it's countersunk, Rubber mallet can do the rest

350's have a bad rep that's for sure... but if you read all the threads on them, it seems people who own them love them. Before you do anything, confirm which model of 350 those are. I beleive by 2018, the "C" version was being made... here's a review of them from 2016 350C introduction I...

What you are describing is exactly how I boat at night. I implement most of what you've heard so far. I run split screen radar and nav map on a 12" garmin MFD. I also have a nightwave low light camera. I run that one to a separate older MFD- the one I took out and replaced with my Garmin...

I can't answer your yamaha specific questions, but I did just repower my 330 express. Went from 3.3l 225's to merc v8 300's. basically, the switch from 3.3L yams (225's vs 250 not a big performance difference) to any manufacturer's 300's on this hull will net you roughly 5-7mph better speed...

Remove the fusion control, Yamaha screen, or the whole tub under the pod. You can’t get to that from the cabin even if you remove the breaker panel. I have an older 330 with the side power joystick and there are covers in the face that came off to expose screws… that lewmar design stinks if...

You can see during this construction pic in the distance some other people have done similar with paver bricks etc.

define "let" lol! 1/4 of the boat slips there have something in this same dead zone between the boats and the large poles they lay down so you don't drive your vehicle into the drink. several "decks" like mine and a few people with tables and chairs set up. I probably took it to the next...

Mostly free too. The deck was my fatherinlaws above ground pool deck that I repurposed. The bar itself is a few pallets I stained. The top is an old piece of butcher block I used to use for a work bench. The umbrella is an old one I used for work- I left the bottom half of it on a Job site...

I built a bar down at my slip lol

I took mine out of my 330 express with some wrenches and just 2 of is. No draining, no tilting, just unbolted,and humped it out. It’s heavy but no need to make a major production out of it. Took an hour. Once it was in the deck, I cheated a little and had my friend pick it up with his skid...

That’s what I’m talking about!

You hit it on the head with the good turnover comment. Once you get the stink out, keep using it… best way to keep it fresh.

I used to be a naysayer because i bought into the dopey nonsense I read on some forums. Then I actually saw a boat with it and I was sold instantly. I'm going into season 3 with mine and I love it. feels so good to walk on it barefoot. And lets face it, it's easier to keep a little dirty-...

There is no need to drink water on a boat this size. It's not like you will be taking weeks long extended trips with no access to land. flush the tank as good as you can to a level of "i'm ok washing may hands in it." Yanking the tank seems extreme. Mine is 20 years old and I get so it...

Do a search on here. This isn’t the only the thread on this. The consensus was time better spent improving what you have. i have an ‘04. I clear siliconed the joint between the horizontal part and the cockpit floor. After it dried I pulled it up and enough stayed that it’s like I put a...

No denying the issue… but IS it an issue or WAS it an issue? Was it model dependent? The ones I've read about are boats from the 90's. are all the 2000's marlins/sailfish, etc suspect?

I've taken to hosing everything down with the juice days before i work on it... if you want to make your life easier, also wire brush or if you have room, wire wheel the threads that you see beyond deez nutz

I bought one of those amazon side mount ones. shrink wrap coming off soon. I'll do a mockup and see if the positioning works out