Search results

I put 9x12 Lectrotabs on my 180 Sportsman, can't imagine running without them. Easy to install, lifetime warranty, excellent customer support. On a small boat, when even the difference between a 160lb passenger and a 190lb one makes a difference, being able to tweak the ride is key.

I wanted to turn my 180's helm seat around so I could get a cooler under the seat but before I did I called GW to find out what the clamp screws anchor into. The told me if the seat anchor screws are removed the nuts under the cockpit sole will drop off and I wouldn't be able to re-install the...

Easy enough to put in a 4" access port if that helps. Also, maybe follow the bow light wiring back to the console. As I've been running through how I might do mine, I though I'd put the outlet between the hull and liner on the port side, inside an access port.

That drawing came direct from GW cust. service. Can't you store the motor shaft in line with the gunnel so you don't lose cockpit space? Want to see pics when done. This guy had some interesting ideas, not a Garmin but still.....

I was hoping you'd get an answer as I'm contemplating the same thing. Since the waterline is almost 36" below the bow can I assume you're going with the 75" shaft? I have a low bow rail that would have to be cut. I was planning on going with a 24V Li battery in the console and run a plug to...

I bought this stuff in bulk when I had 2 Honda outboards, these parts were left over. They are for 25 HP and 8HP Engines 1995-2005 year models. Selling as 1 lot, prices are current list for comparison. Over $250 worth of parts for $125, shipped to CONUS. (1) 06192-ZV7-000 Impellar Kit 25hp...

Lot of stuff on eBAy or try here.... https://discontinueddecals.com/store/c/41-Grady-White-Decals.aspx

When I got my 180 the stripe was all bunged up. I just removed it, I like the cleaner look anyway, and put the money I saved towards the T-Top....... If you're looking for the small round pendant in the middle, decals are available on eBay and elsewhere, not sure if anyone makes the 3D version...

I've had a 20" Jim Buoy Class IV ring velcro'd to my 180 Sportsman's T Top crossbar, I think it's easier to throw with greater range than a floating seat cushion. I will, however, be investing in a throw bag to attach to it, any recommendations as to length and size of the rope? How's this...

I'll second the 943xsv recommendation, I have 2 on my 180, was able to mount them SxS on the console top behind the windscreen.

I put it away....

I have looked into the new Garmin for the 180. On my 180 I will have to remove bow rail to mount it. The bow of the 180 is 36" above the WL (this drawing is from GW). Garmin says that 36" requires their 75" Kraken, $4100 for the white, saltwater version. Add about $1000 for a Lithium 24V...

Wanting more space on my 180 I asked my old Honda dealer about bracket possibilities and he said it wasn't a good idea, moving the engine aft would upset the balance of the boat's design, might have problems trimming and getting it to run properly. Don't know if it's true not but easier to...

I know, I was just giving some info about how much line you can get in the locker, being a 180 owner. FWIW

Nope, just informing you of the amount of rope you can put in there.

The 180 (I own a 2004) will hold at least 300 ft of 3/8 line, maybe a bit more.

FYI, reduced to $25K

Installed a GT56UHD this year, great at low speeds or in flat water, gets a bit grainy in rougher conditions. I've read a slight tilt down at the rear will help, put more water in contact. BTW, what size wrench to adjust?

I bought a 2004 180 in 2019, the bang cap was wonky so I had it removed. The transom underneath was good so it was glassed over and vinyl cap installed. I also installed trim tabs which involved drilling 18 holes at the bottom on the transom. Every hole was dry, I could smell the sap heating up...

Yep, I have a set coming tomorrow for my 180, thanks KYG!