Search results

How long after donating does it take for ads to go away?

if it's the same ASI out of patchogue ny on waverly ave, then thats who I used too. couldn't be happier! Lou is the man!

its been a while but someone before me installeed a fuse block fed by a large 12v feeder. I just added a fuse and tied it in.

My installer said the templates on file are only a starting point. all boats are essentially handmade and have slight variances.

I had Seadek installed and my installer told me that while files exist for many boats, they are only a starting point. All boats are basically hand made and there are variances. he made templates for mine from files off the Seadek installer website and while they were close, he still scanned...

I don't think your question can be answered unless it's known what devices you want to run and how long you'd like to run them. One night on the hook and a trip home is a far different requirement than plans to spend a week out there. Personally, If I had a working generator, I'd roll with...

tough question. I'd start with asking yourself how you will use it and how fast do you need to go? do you just want a turnkey boat and willing to pay up a little for no hassles? Once you get all that figured, then you can narrow down the years of 330 express that would be best. While the...

exactly, AC working means the pump works and water is flowing or the air would not get cold. I have an '04 330 with original AC which cranks... tried heat one time last fall and could not get it to come on but I think I wasn't operating the controls correctly. They are a text book model of a...

I have an '04 and I've gone pretty nuts modifying and upgrading. I've also poured over the owners manual which has wiring schematics and layout of chases- I don't think anything runs through the front pipes. I've seen the aforementioned wires that run through the single pipe next to helm pod...

... half the price amazon countersink tool

I'd find the correct size washer and DIY it using a tool like this: Countersink tool I would def not pay 50 bucks for it but im sure a cheaper substitute could be found. Once it's countersunk, Rubber mallet can do the rest

350's have a bad rep that's for sure... but if you read all the threads on them, it seems people who own them love them. Before you do anything, confirm which model of 350 those are. I beleive by 2018, the "C" version was being made... here's a review of them from 2016 350C introduction I...

What you are describing is exactly how I boat at night. I implement most of what you've heard so far. I run split screen radar and nav map on a 12" garmin MFD. I also have a nightwave low light camera. I run that one to a separate older MFD- the one I took out and replaced with my Garmin...

I can't answer your yamaha specific questions, but I did just repower my 330 express. Went from 3.3l 225's to merc v8 300's. basically, the switch from 3.3L yams (225's vs 250 not a big performance difference) to any manufacturer's 300's on this hull will net you roughly 5-7mph better speed...

Remove the fusion control, Yamaha screen, or the whole tub under the pod. You can’t get to that from the cabin even if you remove the breaker panel. I have an older 330 with the side power joystick and there are covers in the face that came off to expose screws… that lewmar design stinks if...

You can see during this construction pic in the distance some other people have done similar with paver bricks etc.

define "let" lol! 1/4 of the boat slips there have something in this same dead zone between the boats and the large poles they lay down so you don't drive your vehicle into the drink. several "decks" like mine and a few people with tables and chairs set up. I probably took it to the next...

Mostly free too. The deck was my fatherinlaws above ground pool deck that I repurposed. The bar itself is a few pallets I stained. The top is an old piece of butcher block I used to use for a work bench. The umbrella is an old one I used for work- I left the bottom half of it on a Job site...

I built a bar down at my slip lol