Search results

Two Merc 200 hp. four strokes would be the lightest twin engine pair available, I believe. I would consider a single 300 hp Merc, plus a kicker. This would save 300-400 lbs.

Most likely Merc engines, being so light, that Honda sales are lower than they could be. If the BF350 was 100 lbs. lighter, they would sell more. If your boat could handle the weight, the BF 350 would be a fantastic engine on a boat.

https://marine.honda.com/promotions/buyers-choice-sales-event The BF350's are $10K off. A New England dealer has the BF350 for $23k installed!

IF the engines were at 45 degrees, installing 30" shaft engines would raise the inclined lower unit 5"/1.41=3.5".

I have a 228 as well as a 258. I have had a cooler on the bow of the 228 for the last couple of months to keep the lower units almost completely out of the water. This works well, just is inconvenient. The 300 lbs. on the bow brought the lower unit up several inches. The deck is still has a...

If the engines are 25", you could do glass work to raise the engines 5". Then convert your engines to 30". That should bring the lower units up about 3".

A Canyon 306 is pretty large. I suspect you would need at least 4-5 coolers to bring the bow down enough that the drains are too high.

You can also leave a large cooler on the bow, and fill it full of water. It should raise the engines about an inch.

I found an image online of the storage space on a 228. The 228 that I am selling has an auxiliary fuel tank in the location. However in my 258 the space is empty. I could build it out of glass, but if Grady ever made a hatch and coaming for this area of the 258, it would be 10x easier to buy...

I recently purchased a new Rock and Roll trailer. The price was very reasonable, and not that much more than used trailers I had seen online. They are made in FL, but I bought one from their dealer in N.J. The quality appears to be excellent. They could easily build a trailer to fit your boat.

I am thinking it would have a sealed bottom, and use a portable pump to empty it. I would not need it for salmon, but for tuna fishing it could be handy.

That is a cavernous area, below the deck. Has anyone turned that space into a fish box? Ideally there would be a premade, drop in fish box available to purchase.

Thanks for all the replies. I bought the 258, it is being trailered out to Calif., I have not even seen it yet.

I have had Simrad AP44 on two past boats, it worked perfectly. I was careful to install the Precision 9 compass in a central position and away from magnetic interference. I am about to install an AP44 on my new boat, a Grady 258. On this boat, the MFD is Furuno, the radio is Icom. Never had...

I meant non-power assist steering. If the engine died at sea, I could come back on the kicker. The autopilot would be steering the main engine, and the kicker steering would be locked. The kicker puts out a max of 12 amps. With that limitation I would try to keep current draw to a minimum...

What about steering for a single BF350? Is non-powered steering acceptable? I could install a larger wheel for more leverage.

Good condition 228 for sale with aluminum trailer in Northern California. Excellent 2002 3.3L Yamaha F225. New HP fuel pump, injectors, filters, thermostats. Runs great, I typically run at 4,400 rpm and 24 knots. 1996 Grady-White 228 with Yamaha 3.3L F225, runs great. New injectors, HP fuel...

Your BF350 is incredibly fuel efficient.

I just checked, and $25k is a possibility. This is the super discount price. Add sales tax and rigging for about $5k more. I would self install, and have the dealer hang the motor and sea trial.

How far is the cockpit floor above the waterline? What about when crew are aft fighting fish, and the built in cooler is partially filled?