Search results

For, what it's worth, you now know it works as it should.

Looks like the battery charging wire for a second battery.

Have you tried Gauge Saver? I just had my Yamaha Gages refurbed and am pleased with the results.

Not apples to apples but my 2003 200hp ox66 would run hot anytime I flushed it,( hose or ear muffs) Yamaha tech said to run two hoses, 1 to ear muffs and the other to the hose connection (similar to Hookups Y but without the restriction of 1 hose) - no more problems. Not enough pressure? Hose...

The 19 ft Tournament in the pix does not have a deck drain hose. It has 2 scupper drains straight thru the transom on either side of the engine. To answer the question about the circled drains in the pictures, the front drains the insulated box under the starboard bow seat the...

Chris Just stepped out back and measured my 2003 192. Measured 205 inches{ (17 ft 1in) bow eye to transom at bottom of transom. (it's covered) Bunk boards extend 19in over the rear trailer crossmember and boat transom is even with bunkboard.

Ace Hardware here has a great stainless selection.

OK guys. Here's my update on what I've done. Rcvd the cable last Fri. ( nothing but a wire with a 50 amp inline fuse.) Really straight forward install, took about an hour and was no problem at all. (Rigging tube was no problem) Haven't started the motor to check anything yet. Mine is wired...

thanks greatly for all the replies. I've been sitting back and reading all the replies. Great stuff to ponder. It even raised the question I was actually wondering but didn't voice. are the two outputs isolated from each other and/or do they actually work like an ACR and regulate charging as...

I've got a single 2003 Yamaha 200 hp OX66 with 2 Batteries wired thru a Perko selector switch (bat1 - bat 2 -or both). I have found the second charge wire from the motor and there is a yamaha wiring kit to hook the second battery up so they are both charging without having to remember to change...

Merry Christmas to everyone. Hope you have a safe, happy and healthy new year.

https://www.boatoutfitters.com/hardware/gas-shocks

Hope everyone in Fl is safe. Thinking of you as it heads into Ga.

I have a 19 and removed my armrest also. Added a spacer the thickness of the armrest at the bolt holes and added two new snaps to hold the cushion. Lot easier to get in and out now and have more room in the aisle to walk thru.

Didn't want to lose the little storage at the helm that we have. Am able to use the storage and also when I'm standing, the box opens and has a brace so the door stands out about 60 degrees and can be seen standing over it.

Timely thread. Upgraded from Echomap plus 74cv to Echomap UHD 74SV first of this month. Read it wrong and thought it included new mapping - coastal and lakes. Upgraded maps that are on sale are to be delivered today. Hope I got it right this time. Really wanted the 9 inch just not enough dash...

I'm currently using the lift rings with a bridle (tow harness) between them on my Tournament. The rings are close to the water line and the rope stays in the wake. It makes it hard to throw a tube outside the wake for a good ride. That being said it works just fine for my 6 and 8 yr old...

FWIW. I was having the same type voltage drop to my older garmin C/P. it would cause the display to flicker but not go off. Could touch the wire at the Fuse panel and would work fine for awhile. I took the Fuse Panel out, disassembled it cleaned the contacts , replaced the connector on...

Thanks guys that was about what I had decided since I could not find any reference to nmea 200 and 2003 Yamaha. Again thanks for the response.

I can't find any info on this and was wondering if the 2003 Yamaha OX 66 200hp is compatible with nmea 2000. If so, what kind of data would it give me? I have searched and don't see a nmea connector on the motor wire harness.