Search results

  1. Beast of Burden

    307 sureshade trouble :(

    The sureshade control on my 2016 330 Express is located on the starboard cockpit side behind a starboard panel. I think its the same panel to access the hot water. I've played with that control panel quite a few times to get my shade to extend evenly and also contact the upper hooks with the...
  2. Beast of Burden

    Holding tank discharge pump

    Brian. I did that on my 330 once shortly after I bought it. It was something to do with the "duckbill"? flaps inside the vacuflush system. The tech accessed the pump from the starboard side of the midberth by removing a panel and had to "reset" the flap back to the correct position. Sorry I...
  3. Beast of Burden

    Fischer panda problem

    Hi and thanks to everyone who responded to my inquiry. So I had to take the boat in for service to the yamahas so I explained the genny issue to the service writer. They don't have a genny tech on site so they arranged for a visit while it was in their yard. So it turns out there was a bad...
  4. Beast of Burden

    Sump pump on 330

    What year is your 330? I had to replace the sump pump on my 2016 330 and while the box is easy to get to the pump change was complicated by the fact that the old pump was discontinued and the replacement required a higher amperage breaker in the panel. If it is only the float switch however you...
  5. Beast of Burden

    Hydraulic Trim Tabs 2016 Grady 330

    I have the wiring diagram for the tabs but it is not overlaid on an actual boat the way many of the systems are
  6. Beast of Burden

    Hydraulic Trim Tabs 2016 Grady 330

    I believe I have a malfunctioning sensor on my port side trim tab. Both tabs go up and down (fluid level perfect) but the led indicator doesn't track the up and down correctly on the port tab indicator. I spoke with a Bennett tech and performed the calibration exercise several times but the...
  7. Beast of Burden

    Fischer panda problem

    Thanks for all the feedback. I'm inclined start this project with initial assumption of a fuel issue, likely a partial blockage somewhere. IHMBJack I have 2 fuel fittings/lines coming out of the top of the tank. Both are square with threads coming out forming the 90s. Are these the check valves...
  8. Beast of Burden

    Fischer panda problem

    There are no warning lights active when it shuts down - it starts rightn up and runs strong both without load or under full load and when it quits it is just as if you pushed the stop button. Exhaust water flow is strong. I agree it really seems like a fuel issue. Shut down is consistent between...
  9. Beast of Burden

    Fischer panda problem

    Hello and thanks in advance to all feedback. - My 2016 Fischer panda 4200 has developed a problem. It starts easily and runs great with or without load but out of the blue after 5-10 minutes it shuts down. No stuttering prior to shutdown - it is identical to pushing the stop button - it just...
  10. Beast of Burden

    Need advice re: renewing cockpit bolsters

    Thanks for the 411. I do intend to re-cover them (that is what I meant by renew). Does anyone have any reccomendations for a good upolstery shop within a days drive of Tampa Florida?
  11. Beast of Burden

    Need advice re: renewing cockpit bolsters

    My cockpit bolsters have been washed hard regularly for 5+ years now and are looking sad lol and I am seeking advice as to how to renew them. no regrets as quite a few fish have visited- its been worth it! Its a 2016 grady 330. Do they come off easily and how? I'm guessing everyone can...
  12. Beast of Burden

    Power steering out

    Just in case you are still seeking experiencing this problem - on my 330 express there is a factory installed fuse inline in the wire supplying the pump. it is located directly off the battery terminal. I discovered this when after changing out my batteries I had no power to my steering. I had...