Search results

A quick check on eBay showed a number of original Grady rod holders but there’s a premium attached to the name. I wouldn’t be surprised to find Taylor made makes them for Grady. window pulls are and if buy a Taylor made pull its $10, if you buy them with the grady part number attached their $40...

Anyone still running a heavy rope around ? Kinda liked that look.

Here are a couple pics of my transducer placement. I mounted the unit so it hung slightly below the hull and putting it in line with the chine to keep it in cleaner water. As I said I wasn’t sure if the lower unit would block the port side sidescan signal but it’s good.

Yup, agreed. This is where I “slip” my boat.

My DT is doing what it should so no need at the moment. It was Rudy’s marine I got that quote from about two years back. I imagine it’s gone up a little since.

Finally got to put my new Simrad Go9 thru it’s paces today and I’m blown away ! It’s super easy to use and I credit it with putting me on bass today that I wouldn’t have found with my old Faruno. The transducer was mounted on line with the starboard side chine and though I was worried that the...

Reason I ask is because I was watching one of those “boat fails” clips where a newbie yacht owner blasted past a marina rocking the hell out of all the boats in it and apparently prompted a number of insurance claims. Granted that’s extreme but I got to thinking what if I zig when I should zag...

These old tractors were made to rip a plow thru soil so moving trailers are child’s play for them. It’s pretty short and I fabricated a front hitch for it so I face directly towards the trailer making it easy to back it into its spot on the carport.

$10k Saved ? Last I checked I could get a F200 in Delaware for $15k + rigging. Another thing is the DT I’m running now is not rebuildable having a pressed crank and rod assembly which btw is no longer available so when it goes that’s it. Yamaha, OMC, and Mercury’s are rebuildable. Also when I...

What amount do they cover for loss or damage to others property or medical ?

Don’t think you’ll need trim tabs.

Should be the same as on a 20 Overnighter with a Yamaha F200, which runs best with a stainless 19 pitch prop. Tried and proven.

It is simple, maybe a little goofy but it works. I think it actually uses less water than leaving the hose fully open on the muffs with water spraying out everywhere. The lawn wasn’t anywhere near as flooded doing it this way as it usually is and like I said the discharge stream never got warm...

It’s kinda like not reinventing the wheel. The Yamaha F200 weighs 15 lbs more than the 2 stroke DT225 and uses the same bolt pattern. Seen quite a few paired with a 19p stainless prop hung on my generation Overnighter and it’s a decent match. WOT speed is a little less being a 200, 43 mph...

Ya, also when you flush like this it’s that much more obvious what a 2 stroke engine puts out its exhaust. Lotta truth I n this meme... If this engine and I ever part company it’ll get replaced by a Yamaha F200 4 stroke.

Lol That would be nasty ;) Water stayed cool though. looked like a cauldron but clearly provided more water thru the engine than the muffs do, and I didn’t get sprayed with water or wet having to reposition the muffs over and over.

I trailer my boats, always have. I always flush my engine after every saltwater trip and if I haven’t run it in awhile I like to run it on the muffs at home to be sure it’s good to go. Problem is on my DT225 besides the ports that get covered by the muffs there’s a rectangular grate on the...

I would think the stumbling block for electric powered boats is weight. The average Tesla is about 5,000 lbs. which is about 1,500 lbs. more than a comparable engine driven automobile. Their going to have to find lighter batteries if they want comparable performance. Slow is fine for lakes but...

Can always bring a gas powered generator ;)