Search results

This liner crack above the port window has been there since I boat the boat about two years ago. It does not appear to be expanding. Anyone have experience of a fix that that will stop any future expansion and still look reasonably okay? My current thought is to have home depot do their best to...

Tom: I purchased a Mermaid AC unit out of Ft. Myers, FL. I read some good reviews, but I don't really know if they are one of the better units or not. What struck me was that many reviews said they were geared for the do-it-yourselfer and provide greater assistance after the sale. I found this...

Amongst the other practicalities, you'll need to consider where you'll place your through-hull fitting for the condensing sea water water source. Some have placed the thru-hull in the rear bilge and the 500 GPH pump pumped water forward to the unit just fine. I wasn't comfortable cutting a new...

A lot of good information here. I'll add another tidbit that has always intrigued me. The draft of the 271 is 23", greater than any other Grady her size and greater than the 306 at 21" and equal to the Marlin's 23". It is equal to the 23" of a Contender 30st. I asked my dealer about this some...

An access hole is a good idea if I have the space. Thinking it through, I think I could access 3 of the four blind side nuts while tightening the nuts again. But the hole would have to be off to the right, between the support brackets, and likely about 4" in diameter to give me enough wiggle...

Thanks, Tealejr. Freezing up the unit isn’t something that was on my radar. It will be now. In my story above, I left out the part about disconnecting the main duct line from the unit itself when no air was coming out of the vents. I was afraid of some huge tear or other blockage from when I...

It works! Went down to boat yesterday to make some of the temporary pieces more permanent. I.e., cut more holes in the boat. But they had a slip open with power. So in she went. And to my pleasant surprise, all seemed to work. When I first opened the seacock, water rushed through the lines...

Lookin' good, blondie! :) This plexiglass has a unique property. Somehow it filters out grey and restores blonde. Because, believe me, its harder and harder to find anything but grey up there. I know because my daughter very kindly tells me each time she comes home from college.

Accomplished two things since last post. Installed and wired in control box and thermostat and replaced aft berth starboard rear panel with a temporary plexiglass panel. Was ready to test the system yesterday and the marina said every wet slip with a power pedestal was taken for the holiday...

FSC60: Thanks and you are observant! I chose the Groco for its quality but also because it has a large bowl with a threaded plug with an O-ring at the base of the bowl. As Ahill pointed out to another member using a forward through-hull, there will likely be a fair amount of air in the lines...

Finally, the AC is in!! Not yet wired in, but (hopefully) that will be relatively easy. The water supply and exit hoses are connected as well as a drip pan connection to the shower sump. Non insulated ducting runs to two outlets on the steps. I'll add a third when Amazon gets another matching...

Well, looks my post of the new Head to Holding Tank hose didn't take. So I'll try again. Explained situation to guy at Boat Owners Warehouse. They had the same hose I used. He said it is rated for use below the water line but it is not as durable as the better hoses and odors will pass through...

That’s about about how far behind the times I usually am. Wanna see my iPhone 3?

Just to add a thought to this old thread. Seemed to be much concern about adding through hulls. An option for us was to use the holding tank's overboard discharge. We never once used it and had no intention of using it. So it became the cooling water intake source for our Mermaid 6500 btu unit...

I’m 5’8” and I have to use a half-round pillow below my knees to be able to lay flat on my back in the mid-berth. With my knees raised some, not to the extreme, I can be quite comfortable on our custom mattress. Not on the durable, but overly firm mattress Grady provides.

TD: I used SEM Vinyl Coat Flexible Coating M25073 Off-White. It is mentioned in post no. 11. It isn't my discovery, but I have been happy with it. Rob

;)

Says Vin Murray or vmurray@pompanette.com in the body of his posting. You must have missed it.

Grady 33: No, my seats haven't experienced any cracking or tears in 2-1/2 years, fortunately. Peter: That price for a single chair is way above what I paid a couple of years ago. And I'm surprised to see that we can buy the the Grady color now. The price for two is more reasonable (as...