Search results

I had a soft top 228g with a 2002 200hp V6 4T, it was just enough but could use more power, don’t get a 4cyl 200 it will be underpowered, go with the 250 you will love it.

If you go OEM probably 2-3k with labor, call a shop they will know best

MY 02 with a ox66 250 runs great, had problems getting the back end up enough but I realized trimming the bow up a bit and the motor corrects that, in terms of features, it’s a lot better then my last 228g but I do still like the design of the 228 hull a bit more, just different

Boat seems priced about right if it has lower hours “under 700” but can be solid with over that “if maintained”. Make sure the hull is solid and floor has no soft spots or flex, trailers are expensive so unless it’s being dry stacked at your Marina you will need one and they can be expensive...

when I take my flush port off the motor *looking at back of motor* I have to screw it to the right almost like a reverse thread, I tilt the flush port up mimicking the motor connection and tighten the screw on to the hose turning left, is this correct?

Have the yellow rubber piece in there, seals good under normal motor operation but I should check

Reply Thanks, I keep the motor off and I do need to check the fitting but seals good under normal motor operation

I’m not an expert by any means but usually a clean plug means you are burning water which steam cleans the cylinder/plug, the only other stuff would be oil/ gas which would dirty it, I’ve heard of some of these older ox66 motors like I have getting a leak in the head gasket but maybe other...

Strange question but does flushing your outboard with to high of pressure cause any harm? 3 times I’ve ran the hose fully open on the flush port “02 ox66 250” and have been wondering why the pee stream is so strong with some water coming back out the connector, Seems like my Marina re did the...

I’ve just never heard a cracking sound like that, but entire leading edge of dock is cracking and wood looks bad from salt water so that’s probably what it was, side of boat looks the same as before no marks and white

It hit the main hull “under the stripe” at a 45, I didn’t get it sideways enough to be parallel with the dock, where I hit looks the same as before white and perfect, the dock did have cracking all along the leading edge “not from me” so that’s probably what I heard

New to me 248 “I've had 2 Grady’s before” The other day me and my buddy are docking in and out of neutral at a lower speed but faster then usual, I jumped off and the front hull hit at a 45 degree angle, I heard a cracking sound but when I looked, zero damage to my boat and the dock was cracking...

I will drain the bracket whenever my lazy ass boat yard wants to get to doing maintenance on my motor and boat, it might be a while cause whenever I ask how long they say, yes ‍

I have a 228g with a 200 4 stroke v6 and it’s fairly slow but has plenty of torque, I do 32 at 5500 wot

I think that this is the problem cause the Calvation plate on the motor or whatever it’s called sits right under the water but when the bracket is drained it rides just on top when I open her up.

O I have no clue about what prop pitch I have it was a expensive prop from the old owners, I keep it waxed and all with no bottom paint on the boat, I do trim properly when on plain but don’t get much a difference.

About 5 years ago I learned to drive a boat on a 1986 19ft grady and now I use a 1990 23ft grady for boating and both have been very solid in my life, they both have never let me down and don’t be scared of getting a 20-30 year old grady

The boat hull is mint and I just waxed it. It is a 1990 but even the guy that out in are electronics was impressed. I do have to say that one time I took out the bracket plug and a ton of water came out so I’m thinking it might be that cause the stuff that seals it to the boat is all cracked...

I have a lot of shallow spots around me in my river and inlet because people tend to not get the sand out and it fills up, so I blew out my gear case and prop, The gear case case looks good and my prop looks straight, I want to say it’s the same prop cause it’s straight but looks like It was...

Don’t know why I couldn’t spell when posting. Anyways I have a 80 gal tank and I normally use it for fishing offshore or going up and down the icw. I don’t mind it offshore cause I can’t go fast enough but in the icw it kinda sucks. I push 32mph at 5500 rpm with 1/4 of my 80 gal tank