Search results

I've always carried a spare aluminum 'get home' prop along with two sets of prop nuts and washers. If I'm changing a prop in the water I'm guessing I'm gonna drop something. Also, if you're going to carry a spare prop, you'll need a short board to hold the prop in place while you turn the prop...

A call to Grady will likely get you the "Dockside Power Wiring" diagram that will be helpful to you. Pasted below is just an example for my boat, a 2007 Sailfish 282.

I get more than my money's worth from the knowledgeable guys on this site.

Italian: Will the digital autopilot allow you to just idle along on a set heading? I'm wondering if it would be helpful for flying a kite, with the bow into the wind or current and moving forward just at idle speed? Tx, Rob

I'll chime in on the side of having had good experiences when calling for part numbers or info on my 2007 Sailfish. Once I sent a picture of a below deck hose labelled Marine Fuel that seemed very out of place. Within a few days someone answered that is the type of hose they used for the head...

Looks great and impressive numbers!

I went through two RCL-75's. Both died shortly after warranty. For the second light, parts were very hard to come by and no repair service was available. I was disappointed in ACR. So now I've gone with the much cheaper LED light bar. If I have to replace it every year it will still cost far...

I had a 208 for ten years before I replaced the bang cap. I asked dealer to also go over transom as best they could at that time. They found nothing. The only holes in the transom were my transducer that I mounteed myself and I sealed those holes so well and all the way through. I just did the...

Hookup: Nice! Does it slide onto your existing pedestal?

In answer to RobboNJ's question: I bought one helm seat directly from Pompanette in 2019. Couldn't buy it in Grady's color because that is available only to Grady. I bought the Evolution seat for $1,736, with tax and some other fees in 2019 prices. It did not include shipping because I live...

Robbo: Dont' want to hijack this thread, so I'll start a new thread just to answer this question.

Also following with great interest! FWIW, my dealer replaced with the vinyl bang cap about 6 months ago and mentioned no problems getting it then. Wonder what happened since? Good luck with the remake and I hope all looks good when the old bang cap comes off.

A quick call to Grady should give you an answer you can rely on. They are really good at such things. They even helped me track down the right Bennett trim tab part number for my 2007 Sailfish. Or if your seats are made by Pompanette, you can get an answer from them as well. You can likely even...

I have made a mistake. My hinges are not like those on the Overnighter. Apparently, I'm getting my past Grady's confused with current. Still, I went to the nearby BOW, but, unfortunately, they did not have anything like that shown in the photo for the Overnighter. I'm sorry to have sounded like...

Its actually BOW.com. But I looked on their site and couldn't find them either. I will try to get by there over the next few days and see if they have any. Rob

I found replacements at Boat Owner's Warehouse. I don't believe they were the same brand as Grady used originally, but they were an exact fit. Unfortunately, BOW's website is difficult to navigate and doesn't necessarily reflect what you find in the store. Rob

FWIW... I had a hard time accessing the screws without tearing the dried out bolsters. Finally I figured out that I was getting the darn things off to have them redone and tore whatever tore to get to the screws.

JLR: Thanks for adding the closure. Checking for chafing(?) in the middle of a wire run is not something I want to add to my regular checklist!

Cody: Nice looking 258. I'm curious. What props are you running on your Journey? Tx, Rob

Best price I found was from Boat and RV Accessories on eBay. You can put it in your wish list and the next day they offer you 5% off, as many sellers seem to do there. Unfortunately, I only found those with a white ABS plastic handle. Would have preferred black.