Search results

  1. Q

    Installing a boat table

    I'll check out the rubber grip.
  2. Q

    Installing a boat table

    Thanks for the feedback. Yeah, thinking in using a 3/16 flat SS backing plate to help spread the load. I prefer the side mount, similar to want DennisG01 mentioned so that I can have a little more leg room. The table will be flat. Anyone have any ideas on what can be used to decrease cups...
  3. Q

    Installing a boat table

    Thanks Ky. I saw that one. Not sure if the bow fiberglass is thick and sturdy enough for side mount with load. I’m thinking it should, but want to know if anyone had that any issues?
  4. Q

    Installing a boat table

    Planning to install a wood boat table with a removable pedestal side table mount at the bow of a GW235. I know from factory they have a floor mount, but I wanted one that would go on the side so I do not have to walk over a floor mount. Anyone done a side mount before at the bow where the...
  5. Q

    Helm Master Ex Joystick install

    Did not see function to calibrate joystick itself. Just saw thrust level, lock to lock, etc. Is there a way to do that?
  6. Q

    Helm Master Ex Joystick install

    I fish mostly deep water. Occasionally I go to the shallows. Anyone tried to install the joystick on the helm master ex themselves?
  7. Q

    Helm Master Ex Joystick install

    I plan to use the joystick mostly for the stern fishpoint and drift. I didn't want to place a trolling motor and add more weight to the boat.
  8. Q

    Helm Master Ex Joystick install

    Thanks for sending me the link. I will look through it.
  9. Q

    Helm Master Ex Joystick install

    Yes, this is a single engine, no thruster.
  10. Q

    Helm Master Ex Joystick install

    Has anyone installed the Yamaha Helm Master Ex Joystick themselves? It looks like a plug and play. I tried to install the joystick on my GW 235 while on a trailer, but it seems to not be linking up. All the rigging looks good. The yamaha display recognizes that the joystick is in place (I...
  11. Q

    Yamaha Helm Master Ex Joystick instructions needed

    Hi all, I had the joystick installed on my vessel. But it didn't come with any instructions. Does anyone know if the outboard is in neutral idling, should you be able to move the outboard back and forth just like you are able to do with the wheel? On the joystick, it does have a button that...
  12. Q

    Lighting of Electronic switch panel

    Thanks for sending the diagram. I will plan to order a couple along with the tool.
  13. Q

    Removing cupholder

    Good ole' heat worked (for a prolong time) with a lot of pushing, pulling, cranking (I needed to call the Incredible HULK) and cutting. They did a good job in sealing that cupholder to make sure no water seep in (a little overkill...but it would do the job to not let water in)! Thanks all for...
  14. Q

    Removing cupholder

    Thanks for the ideas. I tried to rock it back and forth with a great deal of force from underneath (it didn't budge); used the plastic prybars (couldn't get any of those really underneath the cupholder lip to pry it lose). This is some secure silicone.
  15. Q

    Removing cupholder

    It is stainless steel cupholder.
  16. Q

    Removing cupholder

    Hi all, I want to remove one or two of my cup holders, particularly the one at the helm on my GW 235. Does anyone have a good method in doing so? I tried to cut around the perimeter with a utility knife (carefully not to cut the coating) to cut the silicone, but it is not getting underneath of...
  17. Q

    Lighting of Electronic switch panel

    All of my wiring to the back of each daisy chained rocker switch is tight without corrosion. I would assume it’s not a ground issue, because if so, then none of the illuminations or indicator lights on the rockers would be working. Possibly bad 2 rockers, but I would think this is unusual since...
  18. Q

    Lighting of Electronic switch panel

    Thanks Chris. I will look into it. Do you know if the bulbs are easy to replace? I assume it is a bulb in the rocker that I need to disassemble and find out the bulb number to replace. That is if they are replaceable without having to buy a new rocker switch.
  19. Q

    Lighting of Electronic switch panel

    Thanks for the info. Yes, went out and pressed the nav/ancrocker switch and the other switches illuminated the symbols on each switch except for the bilge switch. I did notice another switch light was flickering. Are there individual bulbs on the back of the GW factory installed switches that I...
  20. Q

    Lighting of Electronic switch panel

    I have a 2022 GW 235. Does the entire switch panel suppose to light up so you can see what the switches are at night? My board only lights up the one button you activate. I would like to see what the button are at night without having to turn in the hardtop cockpit lights on. That is, after I...