Search results

mine are just right......... :wink:

:lol:

Sorry for the intrusion, Not a Marlin owner. I run each tank at the same time I run my port off one and the starboard off the other. In my mind that keeps fuel fresher and the idea that both engines are independent if fuel were to be an issue. I normally will keep 1/2 to 5/8 at the most. I don't...

Thanks, helps until I get the full info, top rpm and speed with best cruise economy :goodjob wise

What is your main cruising rpm and speed, in the ocean under moderate conditions 2-3 or less. please :hmm :sorry fuel burn, and your top speed and rpm in flat water? Thanks for your help! :dance

Two things, did you have spacers put in the holes of the hardtop? they would go the exact thickness of the hardtop with the bolts passing through them. Also , have a plate made wider than the rigger base for the top. If you don't you will only squeeze the hardtop flatter and flatter with the...

who has one? where to get one, and how much should it cost. What size is it? :hmm To be able to se into the over head electronics box and to see over the wind shield if needed. :wink:

two engines and two hds tens. to display all engine data, and hooked together via Ethernet cable, :wink: the auto pilot is also run to the hds as is the vhf

yes hds-10

I want to run the digital cable from my engines to my dash The boat is a Bimini 306, how long a cable a n extensions do I need. :hmm Please be specific. :sorry

GET EM THEY ARE A TON BETTER THAN ALUMINUM, LIGHTER AND STIFF AS AN 18 YEAR OLD!! :dance

removable rod holder, for the stainless , down rigger mount for the black plastic(or a leash pin holder for a rod security leash)...looks like a pin goes in the hole :hmm

:shock: ap-24 installed ,trolls perfectly runs 30mph perfectly, put the pump in the compartment near the electric fuse panels in the upper compartment in the center console. No major install, my mechanic installed it in less than 3 hours, (HARDEST PART was the return line to the helm access) set...

Re: Best Compound and Wax to use to bring back the grady hul what about the splatter non skid on the cap of the hull? I had the inner hull sanded and buffed but he did not do the non- skid and it is white compared to the hull color next to it in the smooth parts...?? :huh

screw a bigger than the hole piece of 1/4 inch wood into the existing holes covering the old hole from under the bottom and mark the exact center. buy a hole saw the size you need with along center bit and drill the new hole nice and straight , slowly. and carefully. This is no different than...

Sorry if you took it personally. :cry: But I had asked fairly straight forward questions and was not getting direct responses. So I went to look at boats. I happened to find the first mate cleaning the tender , which happened to be a 306 bimini with 225 Yamaha 4 strokes. I asked him where the...

It is interesting .THANK YOU FOR YOUR REPLY'S!!! I went to look at an identical 306,but it was a 2002. It had ap-11 and a rpu80 pump. This guy uses the boat as a tender and pulls it behind a 72 foot Hatteras. He prints money, when need be. I feel if the pump, which is in the center console shelf...

Re: What pump did or do you have?? :hmm

thanks guys. I have two cylinders and a tie bar ....75 % of the installers said that is what they installed rpu80 , only 2 of 7 people said I would notice the difference between the pumps. The bigger issue is keeping the pump as close to the helm as possible. This eliminates any major flow rate...

who has an ap-24(03) simrad virtual feed back Postby NO REGRETS » Aug Thu 15, 2013 2:51 pm hopefully you have had at least a similar one, if not the same one with the rpu-80 pump. Where did the pump get mounted, and where, if you have the virtual unit, did he put the compass???? And the...