Deck hatch re-core 265

SkunkBoat

Well-Known Member
Joined
Oct 12, 2017
Messages
4,137
Reaction score
1,435
Points
113
Location
Manasquan Inlet NJ
Website
www.youtube.com
Model
Express 265
Been juggling projects desperately trying to complete before scheduled launch...

Got this one done. Tank hatch was a little wet and glass came loose from edge. debated doing a partial repair but when I got into it I didn't stop.
I had a nearly full big can of West epoxy and some glass lying around. Turned out I needed another $100 can....and hardener... I should have used polyester resin but those West pumps are so easy...

Taking guesses on before and after weight of the hatch. Closest wins 10,000 Non-redeemable points;)

8X6kM5Jm.jpg
8O1qBC5m.jpg

bWoJB3xm.jpg
ZDxsQMGm.jpg

tDjJQLRm.jpg
3zZ9fAEm.jpg

I tapered the outside edges of wood blocks 45 deg and dipped the glass down
then filled with thickened epoxy

Wood is 1/2" AC exterior pine. Not what I wanted but it was a reaaly good board...clear on both sides. Had a couple voids but not bad.
Can't find any "Marine grade" AB exterior douglas fir.

chopped strand mat then "buttered" wood squeezed down then gaps filled then chopped strand mat then some tabs of chopped strand mat then some tabs of 1708 and some old leftover light glass cloth
 
Last edited:

Hookup1

GreatGrady Captain
Joined
Oct 16, 2007
Messages
2,543
Reaction score
709
Points
113
Age
69
Location
Cape May, NJ
Model
Islander
That looks great! And you should have no regrets for using the West epoxy. Polyester is not a good choice for doing repair work.

The deck screws are the most likely place to fail. I over drilled them, filed with epoxy and re-drilled them. Reinstalled using 3M 4000.
 
  • Like
Reactions: PointedRose

SkunkBoat

Well-Known Member
Joined
Oct 12, 2017
Messages
4,137
Reaction score
1,435
Points
113
Location
Manasquan Inlet NJ
Website
www.youtube.com
Model
Express 265
I just put it down. Used 4000UV also. Hopefully its not too hard to remove.

When I took off the beckson round ports, the GE silicone was stuck firm to the gelcoat but not adhered to the plastic rings at all. Definitely dripping on tank.
Thats what made me try the 4000 this time. I'm going to take up the motorwell becksons and re-seal them.
I realized the rings can be sealed down with something substantial because normally you are only removing them when they are shot.

Funny though, there is "Use Silicone only" imprinted right on the inside of the rings!

Silicone had worked great on the edge of the hatch where its gelcoat
 
Last edited:
  • Like
Reactions: PointedRose

Hookup1

GreatGrady Captain
Joined
Oct 16, 2007
Messages
2,543
Reaction score
709
Points
113
Age
69
Location
Cape May, NJ
Model
Islander
I wouldn't expect any significant weight change. I like the 3M 4000UV and plan to use it more often. Seems to be a better adhesive than silicone and it resists mildew. Deck ports are problematic but 4000 will help. I'm tempted to clear silicone the caps on for as often as they need to opened.
 

Vlabruzzo

Well-Known Member
Joined
Jun 11, 2020
Messages
56
Reaction score
7
Points
8
Age
46
Location
Long Island
Model
Tournament 225
That looks great! And you should have no regrets for using the West epoxy. Polyester is not a good choice for doing repair work.

The deck screws are the most likely place to fail. I over drilled them, filed with epoxy and re-drilled them. Reinstalled using 3M 4000.
Why do you feel poly isn't a good choice? Grady were built with poly. Also, gel coat isn't best on top of epoxy from what I understand.
 

Hookup1

GreatGrady Captain
Joined
Oct 16, 2007
Messages
2,543
Reaction score
709
Points
113
Age
69
Location
Cape May, NJ
Model
Islander
Why do you feel poly isn't a good choice? Grady were built with poly. Also, gel coat isn't best on top of epoxy from what I understand.
Polyester is inexpensive and works well for new layups of boats. It's hard to bond to (poor adhesive properties). Its fine for cosmetic repairs (think Bondo) but if you are doing structural repairs epoxy is a far better choice.

 

SkunkBoat

Well-Known Member
Joined
Oct 12, 2017
Messages
4,137
Reaction score
1,435
Points
113
Location
Manasquan Inlet NJ
Website
www.youtube.com
Model
Express 265
In the case of this hatch cover, polyester would have been good choice. I had a clean, sanded original piece...the "skin"...and I was building everything else new. I don't need to gelcoat the finished product.

Polyester is HALF the price. I would have saved $100. ...except I probably would have miscalculated my pot time and wasted a lot ( heheh alot more than the epoxy I wasted).

and I hate the smell of poly.

I already had some West epoxy and slow and fast hardener and the pumps and filler.
 
  • Like
Reactions: Vlabruzzo

Vlabruzzo

Well-Known Member
Joined
Jun 11, 2020
Messages
56
Reaction score
7
Points
8
Age
46
Location
Long Island
Model
Tournament 225
Polyester is inexpensive and works well for new layups of boats. It's hard to bond to (poor adhesive properties). Its fine for cosmetic repairs (think Bondo) but if you are doing structural repairs epoxy is a far better choice.

Won't argue those points, still not advisable to use gelcoat over epoxy.
 

Hookup1

GreatGrady Captain
Joined
Oct 16, 2007
Messages
2,543
Reaction score
709
Points
113
Age
69
Location
Cape May, NJ
Model
Islander
Won't argue those points, still not advisable to use gelcoat over epoxy.
I agree. When I repaired my anchor locker hatch I sprayed it with a 2-part polyurethane primer before spraying gel coat.
 

DennisG01

GreatGrady Captain
Joined
Sep 1, 2013
Messages
6,744
Reaction score
1,188
Points
113
Location
Allentown, PA & Friendship, ME
Model
Offshore
Won't argue those points, still not advisable to use gelcoat over epoxy.
Actually, while that has typically been the thought in the past, it's been proven that gelcoat bonds perfectly well with epoxy. Possibly it was based on older formulations of one or the other.

And, yes, poly would have been completely suitable for the job. But, like Skunk said, it's a bit harder to work with (pot life) and is quite stinky.
 

Hookup1

GreatGrady Captain
Joined
Oct 16, 2007
Messages
2,543
Reaction score
709
Points
113
Age
69
Location
Cape May, NJ
Model
Islander
Actually, while that has typically been the thought in the past, it's been proven that gelcoat bonds perfectly well with epoxy. Possibly it was based on older formulations of one or the other.
It's my understanding that it may interfere with the curing of the polyester gel coat resulting in a sticky finish. Do you really want to take that chance on your project? Could have to do with formulation changes over time.

I'm not taking any chances. In fact I may move off using gel coat altogether and go to a marine 2-part polyurethane for finish coat.
 

DennisG01

GreatGrady Captain
Joined
Sep 1, 2013
Messages
6,744
Reaction score
1,188
Points
113
Location
Allentown, PA & Friendship, ME
Model
Offshore
It's my understanding that it may interfere with the curing of the polyester gel coat resulting in a sticky finish. Do you really want to take that chance on your project? Could have to do with formulation changes over time.

I'm not taking any chances. In fact I may move off using gel coat altogether and go to a marine 2-part polyurethane for finish coat.
With what I've read and seen over the last 5 years ago, yes, I would have no issues in doing it. At this point, it's kinda like the old suggestion to never store a battery on concrete because it will cause it discharge... which also is no longer true (but used to be a long time).
 

Hookup1

GreatGrady Captain
Joined
Oct 16, 2007
Messages
2,543
Reaction score
709
Points
113
Age
69
Location
Cape May, NJ
Model
Islander
Epoxy was the right answer. No looking back. Nice job!

Weight? Looks like less angels on the pin head.
 

pmgia

Well-Known Member
Joined
May 7, 2021
Messages
45
Reaction score
15
Points
8
Age
54
Model
Advance
I had mine redone with Coosa. It’s lighter and stronger than before. No chance of water getting in there again. Someone had put a small hole under the leaning post for a wire that leaked water into the core and saturated the tank cover. Better than new now. I did the small cover too, didn’t need it but since we were in there I didn’t want issues later.

567E39B0-B49E-49C1-B124-218B2CE9E295.jpegA51EC777-69EE-4F8B-9DE8-CE67AC82823B.jpeg
 
  • Like
Reactions: Meanwhile