Search results

I use a 100 tooth plywood blade and the amount of "starboard" dust is humongous. Sticks to everything, and unlike fine saw dust doesn't just disappear outside. Inside sticks to everything (static cling?) and hard to clean up. Does not sand as well either, imo. Cannot glue, only mechanical...

My Axiom MFD which is used with EV150 AP does not have sonar capabilities. When bought 2 yr ago who knew you could buy one that did not have that capability, I did not. Considering adding a module. Wondering if anyone has a suggestion. Fish offshore 50-500 ft,

Just got 2 TLD 20's and same custom rods. There may even be more! Maybe I will open a tackle shop.

5k to fix before they hung the engines. Apparently older GW are known for this problem.

Ditched one spinning, to far gone, and gave away a bait caster. Gonna keep the boat rods. The Penn reel also looks like a goner.

Just put Suzuki df250's on my 92 280 Marlin. Was worried about weight but after only 5hrs seems ok. My transom was bad, make sure they look close at that.

Left side almost done, cell phone holder going in to right of gauges. Not sure what to put under gauges yet. Raymarine MFD does not look much different but it now sits in 1/4 starboard instead of 3/4 cutting board painted black. The mfd went to deep and hit the old Yamaha key switches, thus...

Lovely lady in the neighborhood just moved to the midwest to be with her kids. The husband passed a few years ago. At a going away party last night the guy helping her pack up her last few things told me she had some fishing stuff to get rid of did I want it. Sure I say, thinking its probably...

Putting new dash panel in to get rid of old Yamaha holes in the dash. I wont lose memory and settings when I disconnect to feed harness will I?? Dont want to have to reconfigure just now. thanks

How to cut rectangular switch holes....call New Wire Marine. Material and holes for less than 2 fish tacos and a beer. Ray Marine is my mfd for auto pilot EV-150, best thing I ever put on the boat

I see you drawing specs show 3.5 in hole for gauges. 85mm is Suzuki spec thats just under 3 3/8 in. I was going to order a 3 3/8 hole saw online but much easier to buy a 3.5 at HD. Thoughts??

How do you bleed after opening system? I usually call my mechanic, he has one of those pump systems.

Whoa!! A thumbs up from Skunk Boat and got my gauges to read the senders, its been a good day!

Not sure what you have on your boat, but you probably have something other than engines. Radio, VHF, GPS, Sounder, etc. If you do then you should have a house and start system. Your OX66 may have and auxiliary charge wire, you can look at the cable coming from the engine in the bilge and you...

So crisis averted. Pulled sender wires off main/aux switch. Extended them enough to reach port gauge harness and plugged into red wire/tank 1 and blue wire/tank 2 connectors. Hijacked a good ground in the helm box and ran 10ga wire to port gauge. Using 10/12 butt connector spliced the 10...

Just left the dealer/installer and am not thrilled. Still not sure why they did not connect sender wires from tanks to the SMG4s. They just did not give me a straight answer. They did connect the main tank wire (red) which comes OUT of the main/aux switch and a black wire to the engine one...

Also any ideas on how to set up the new gauge panel, same material 1/4 starboard. There will be lots of room and not sure how to fill it up.

Any tricks for cutting rectangular switch holes. I have some 1/4 in black starboard clone

Today tore into the switch panel to find sender wires and clean up unused junk in preparation for a new panel in the future. Punctuated by I phone falling in canal. Depth 6ft, time of immersion 3 min, adverse effects amazingly none! Have the sender wires isolated and now need to know how to...

Knowing where the tabs are during use would make them more useful. In my limited experience once used on the water I am not sure where they are until the boat is back on the lift. On my boat the penalty for touching the tabs is keel hauling!