Search results

The folks at Envorinex were great!. Got a complete kit for about $30 so now I have spares. https://envorinex.com/sheer-drawers I did have to drill new holes.

They people at Envorinex responded quickly and have what I need. I will you know what the cost and shipping time turns out to be. The are very nice and professional. My past dealings with Aussies have been similar. They are excellent people. saludos

The corner guides for the under seat drawers are made by Sheerglide. Looks like they are available in Australia, maybe, I have sent them a message. Anyone purchase there locally? thanks in advance Art

I have come to conclusion that this is not OEM. So I'm going to sand in place. Never worked on teak before, but the one spot I did restored very well. Not I need to buy a mini sander and a face mask.... HA a face mask...

Hi. I searched but could not find in the forum or on the trim. Need to restore badly neglected trim, but cannot find the screws. Thanks in advance

Hello; Thank you for your support. I decided this winter would be a good time to tackle the plastic thru hull fittings. The inspection revealed cracking on the port-side deck drain. I also became aware that the previous owner(I have had her 3 years) jammed a small fitting in to the original...

Thanks so much. You guys are great. Here's another question. Should I stick with the "pry open hatches" or convert to screw hatches? I have four on the floor. The pry open seem to be easier, but I feel the are not as water tight. saludos

Hello; Thank you for your support and advice. I have removed the flooring over the gas tanks of my 1990 seafarer. The two floor boards are held by screws and caulk. After some tank fitting maintenance and clean up, I will reinstall. The question is how to recaulk with the boards removed...

if you have cable steering and a 4 stroke engine, you will love hydraulic steering. Remember manual over power steering? The last time a drove a cable steering on a friends 150hp yami , I had to wear a leather glove to protect my hand. If you don't want to buy new and you can install a...

Yes, thanks. Each panel removed has a hatch to reinforce the void. The rear has a framed and bolt piece of 1/2 starboard, the console panel has a tempest hatch being inserted. It's amazing the amount of screws in the console that have wire damage potential. This is my second Grady rewire...

After three months on leaning into this small access hatches I started cutting her up. Transom Console 2 group27 Life line batteries. I separated the house from the starter and combined them with a Yadina. saludos

Hi Again; Here are a few pics of what I'm dealing with: See the pulpit bolt will be inthe way and I need to cut the top as I will still want the bolt attached. The bow ring hardware needs to be covered with glass for a snagless locker. I'd like to use 20ft chain 200feet of rode. I also...

Hi guys; Thank you for your support. This is a really great site. I want to install a windlass on my Grady. I need to alter the pulpit to mount the motor and was wondering if anyone has done this before? Any advice would be great. Thanks Art

Hi Tom; thanks for your support. While trying to determine the place for the pump to install, yes I removed the protective cover. While fitting the pump into the side wall bracket, without the protective cover it banged the wire mounted into the ferrite bead resistor thingy. This was a...

Purchased the 18x12 Bennett and finally installed them. Since I had never done it before, I had to wait until I could get help creating the negative angle. Bad: 1. The wires nounted on top of pump are unprotected and easy to chaff while determining the clearance. 2. The pump mounting bracket...

Thanks for all the help. I'm going with the 18x12's My off-plane fuel consumption equals my top end consumption. I'm hoping this addition will change that. Saludos Art

Thanks for the info NJ-John. What size Lenco did you buy?

Thanks for the input. I was about to buy the 12x12, but your info and the info on Bennet looks like the 18x9 are the best fit. Looks like the acuator needs to be about 10 inches minimum. ----talked to Bennet and they recommended the 18x12's and the acuator is 13-3/4 inches so I should be good...