Recent content by Finatic

  1. F

    Pulpit and railing wanted

    Pics sent to your email.
  2. F

    Pulpit and railing wanted

    I have a the full railing that should fit your boat. I sold the pulpit a few years ago. Send me PM with your email address if you would like some pics.
  3. F

    transom cap (bang plate)

    Trapper and Dennis, Thanks for the replies and solid information. I spoke to a local Grady dealer today and they said it was a $400-$500 job. Just wanted to get an idea of additional cost ahead. I have a survey scheduled on the boat in 10 days so hopefully the core is dry and I can proceed...
  4. F

    transom cap (bang plate)

    That looks great. Nice job. If you don’t mind me asking what did the replacement bang plate cost and how many hours were needed for the repair? Reason I’m asking is I’m looking at a Grady that needs to have transom cap replaced ASAP. I’m going to be at the marina’s mercy if I proceed with...
  5. F

    What can you tell me about the 257 Advance?

    Dave - agreed the 257 is a great boat and I think my next Grady will be the 282. How do you like yours? Also, I sent you a PM regarding your seat and bolster repairs. Thanks.
  6. F

    What can you tell me about the 257 Advance?

    I believe the 257 Advance has the greenwood plywood in the transom which apparently is not supposed to rot. I would however make sure all transducer and other screw holes are well caulked for extra precaution. I have a 2005 Advance with twin f150s and it is a great boat. I rides well and cuts...
  7. F

    Grady 257 Fisherman. 200 vs 150

    I have a 2005 257 with F150s and when the engines are tilted up they are generally completely out of the water. If they are not raised with the steering straight mine will have about 1" of the lower unit in the water. As far as performance is concerned, I think it's the right combination. I...
  8. F

    Towing a 24' walk around?

    I think you will be fine. I have a 2012 Tahoe with the same package and I used to trailer my 232 Gulfstream with it and now I use it to tow my 257 Advance. My boat is wet slipped and it is only trailer twice a year unless there is needed maintenance of hurricane coming up the coast. I...
  9. F

    Clamp On Center Rigger?

    I don't use a base but I made a plastic sleeve to fit over the base of the outrigger. By sound that it is more secure in the center rod holder of the t-top. From there I run an outrigger line towards the outer most t-top rod holders. This set up is very simple and has worked well. Sorry I...
  10. F

    Clamp On Center Rigger?

    I use an 8' a Taco center rigger on my 257. Instead of the clamp on mount I use the rod holder on the t-top. My center rigger is double rigged. I hope this helps.
  11. F

    2002 282 coming pads

    Under the bolsters there should be a few small grommets. Instead of each grommet is a small screw, loosen all the screws and lift the coming pads straight up. There are small brackets that hold each one in position when they are re-installed.
  12. F

    yamaha mechanic

    I'm out of Ocean City, MD and I've had Shorts Marine in Millsboro, DE work on my Yamahas for the past several years. They have a mobile mechanic, Greg, who is great. He has been able to diagnose things quickly and get any issue addressed fast. Good luck.
  13. F

    1995 272 Sailfish

    That seems like a pretty fair price if everything is as stated. I doubt though that the carbed engines will give you 1.5mpg. Hopefully someone else can provide some real world numbers. Good luck.
  14. F

    Checked out a boat and need advice.

    Thanks for the reply. That's a great suggestion about removing a screw or two to check out the dryness of the transom. What's your thoughts about the small hole that has corroded through the aluminum? What would cause this? My thoughts if I end up with this boat, is I'll patch the small hole...
  15. F

    Checked out a boat and need advice.

    I've been on the search for my next boat and I took a look at a potential boat today. Overall the boat was in good shape but my only real concern dealt with the aluminum trim that is mounted under the engines along the transom. I know there is proper name for this piece of aluminum but don't...