Search results

After striking out in the Search department, I will ask: My friend has an Evinrude 150 , e tec ,two cycle motor. He hasn't used it here in Florida for about 6 months. Upon successful start up the "check engine" light immediately came on. All oil levels were checked prior to start up. Any...

I have a 1995 Yamaha 200hp,2 cycle outboard on my 95 , 223 Tournament. I have found a used Yamaha prop for sale. It is a Right hand, 15 3/4" x 13 degree pitch ,Saltwater Series II, SDS. Could this prop be compatible with my motor? Please comment. Thanks

Good morning, I am considering installing Hydro Turf decking on my 95 , 223 Tournament. I am looking for feedback regarding longevity, ease of install etc. Thanks in advance, Capt 1947

I am thinking of putting a bimini to shade the forward vee seating area of my 95, 223 Tournament. I would appreciate any first hand feedback/picture of the install and practicality of same. I do have a standard bimini for the cockpit. Thanks, capt1947

Good morning, I am currently in the market for a used trailer for my 223 Tournament. I would appreciate suggestions as to the most compatible trailer, ie: easy loader, float on, magic tilt, etc. for my 95 Grady. As I said, a gently used trailer. Will most likely get used 3 times a year for...

Does anyone in the forum have any first hand experience with trailering a 22 Tournament on a tandem trailer, pulled by a late model Nissan Frontier, six cylinder,two wheel drive. My concern lies with the truck's ability to pull the boat , up a typical, paved boat ramp. Level ground should not...

I would like to install an aft cockpit bimini top and frame on my 223. I would like to incorporate this new top so it zips and joins the trailing edge of my existing bimini top. My question is: does anyone have this arrangement and if so is it custom or is there a company out there that has...

I am looking for replacement O Ring gaskets for the inspection plates in my Grady Tournament. Any help on where to get them is appreciated. Thanks Capt 1947

I have a 95 Tournament 223 with the pomp. ladder back helm seats. I am looking for a reasonable parts source for the fittings, operators etc for the units. Thanks, capt1947

Hi, I am hoping to get some information regarding replacement parts for my helm seat. I have the upgraded synthetic, ladder back , arms ,swivel, sliding seat . I think this was originally by Pompanette. Is there anywhere I can get bushings, slides etc. in SW Florida? Any help is appreciated...

Hello , I am experiencing theft of fuel . My Grady is a 95 Tournament 22'. I have not been able to find a "factory" fuel fill insert to try to prevent more theft. I really don't want to install a hasp and lock, unless I have no other option. I believe the filler neck fitting is a Perko...

Hi, I have the need for a locking gas cap for my 95 223 Tournament. Several of my marina neighbors have been hit in the last few weeks. Any suggestions based on experience and use will be appreciated. Thanks, capt1947

Hello, I am begining the research process regarding the addition of a "get me home" outboard for my Tournament. I have the standard notched transom with a platform and boarding ladder on the port side. I am looking for info for the type of bracket, long shaft or short, lift vertically or tip...

Hi, My helm seat ( upgraded ladder back,with arms type) has lost much of the plastic guides that insure the seat slides without wiggle or metal to metal friction. Does anyone in the forum know where I can get some replacement parts for this? Thanks in advance

Hello all, I am experiencing the following when I attempt to start my engine. Batteries are charged 12.9vdc. Turn key to start, the spring gear on the top of the starter spins but does not rise up to engage the flywheel. I would appreciate your comments as to what may be the problem. ie...

The 1995 remote oil tank in my 95 223 tournament did not have a oil squeeze primer bulb. Before installation, I would like to know if there is a standard or common location in the oil line, for it. Comments are appreciated. Thanks

I have have been working on my oil transfer pump/remote tank on my 95 223 with a 200 yami,two cycle. The existing pump mounted on the remote oil tank appears to be too worn. I got it to run but doesn't put out the pressure/volume. What I am considering doing is to install a small 12v pump...

Good morning again, Does anyone have experience in building or using a battery type hold down to take the place of the metal, factory hold down plate system? I know of the substitute stainless unit but I would prefer not to go there. The tank is the yamaha 10.5 litre plastic tank...

Good morning, I have been working on the failure to pump oil from my remote tank to the main tank on my 95 yami 200. "Seasick" was quite helpful in his diagnostic advice. Here is my question. I have removed the 12 vdc transfer pump and integral motor from the remote oil tank. I have broken...

While running yesterday, my low oil warning buzzer went off. Found the oil reservoir was below the minimum. Glad the sensor and alarm work. My question is this. I shut the engine off then turned the key to on. This should activate the transfer pump, I believe. Nothing happened,no motor pump...