Search results

I need a little help with lighting. I lost power to the headlight, the aft cabin light and now the horn don't work~~~~ The owner's manual is only good for wire colors. For example it states all cabin lights terminate at the main fuse panel. This is incorrect, main cabin lights terminate at a 10...

I have a custom made LOADMASTER from Ohio. Stainless, 16" wheels 3-axle, Kodiak stainless disk brakes all wheels (electric over hyd). Best there is out there, it's a tank with more weight capacity than I will ever need. Call Gary at Loadmaster in Ohio.

WOW; Very nice job.

Tuna fishing, 7 to 13 rods depending on crew and weather... and bite. Striped Bass fishing the Chessy Bay, different game.. Fall and spring runs of trophey rock.... Planer boards, between 75 feet and 125 feet from the boat depending on traffic. When I have a good crew we troll 20 lines, last...

From my point of view, I just expected things to be cleaner and more finished. And, sorry to say, not everything is completely "treated". I replaced several bulkheads on my 02 Gulfstream in 2005 because they were rottting on the edges. The more I took apart, the more exposed untreated wood I...

Nice fishing Grady Fish. Its been spotty down here off oc.

I had a 2002 Gullf Stream and I now have a 2002 282 and I observed the same unfinished or roughly glassed over areas where you don't normally look. I have taken every single pannel and port cover off my 282 and I am suprised at what I see each time. The 282 is a great offshore boat and I...

Jim, I for one appreciate the direct and open response from PM. I just fried the factory installed charger (bilge filling with water is another story) and I need to replace it. I'll email you directly.

Trailer Mine is a 282 Sailfish; they are close but I think the Marlin has a 10’ beam vice 9’6”. Regardless, it’s a big boat and it needs a big trailer. After a lot of research I selected Loadmaster of Ohio. My trailer was custom built for the boat. You are going to need breaks on three...

Now What Ok; so what can be done to get ahead of the issue. If I have my 225's inspected and they come back clean, just wait until the day comes. Or, can I take action now that could save me bigger bucks in the future. The figures posted thus far look like $6-$7k ish after a problem is...

Get the permits. I have made the trip from Annapolis to Jacksonville and Islamarida several times. I have been inspected once when I towed the 232 and twice when I towed the 282. North Carolina was the worst. Short hauls, I don't bother. Long hauls I get all the tickets the ride requires...

Cheers Mate and a bleated happy Aussie Day. Tonight we are getting 30+ inches of snow ... Would't minde being on Maggie in the morning vice facing a long drive way to shovel!

Watch your Grady Bilge While running home from the Baltimore canyon last year one of the anglers asked if all of the water comming out of the bait well was "normal". He was sitting on the hatch and water was pouring through the closed hatch onto the deck. I pulled the throttels back opend the...

I hear a lot of talk about putting the boat up for the winter. Are you kidding, not us. Still Rock Fishing in the Bay, and Offshore Chasing Big BFT and deep dropping on the edge when we can get there! Anyone else! Jekyl; you don't count! I could only wish I lived in Queensland!

NOT ENOUGH TRAILER for that boat. Contact Gary at Loadmaster in Ohio. He will custom build your trailer. If you are going to keep your boat on a trailer, don't cut corners. I have full size 16" wheels on mine.

First the Round-Tuit and now the Canyon Draggin', we are on #2 and happy with the decision to stay Grady. We looked long and hard at trailer boats; the 282 is a perfect fit for us. Although I really like the looks of the 305!

I put over 1000 offshore canyon running hours on a 2001 Gulfstream with an ox66 225. She ran great at 4700 to 4800 RPM which was about 26 to 28 Kts. On a typical trip out ~70 mile average, we would burn about 100 gal of fuel each trip. Not to mention the fact that the eng is working hard at...

Mine were/are aluminum, I have had the same issue and I am replacing every clamp I can find.

The pannels were custom made by: Scott Cambra Vector Imaging (508) 730-2954 www.vectorled.com scott.cam@verizon.net scott.cambra@vectorled.com 153 Barnes St Fall River Ma, 02723 First class job, not expensice and they were done in a few days.

Here is a look at two HDS10 units flush mounted on the Canyon Draggin'. http://www.rdtkl.com/images/Fish%20Pict ... 0_4004.JPG I need to put in a small access door like Bill did, that will be handy!