Search results

I had similar oil residue on the bottom of the cavitation plate on my 115 sws after winter storage. I store it in the down position during the winter season. I found that a small amount of oil leaked around the O ring on power tilt rod and ran down the housing. I did not use fogging oil and...

Make sure holes in gasket and flange are properly lined up to tank holes. Mine were not evenly spaced and only a couple would align until I figered it out. :bang

Mount w/o antenna might have been foe LORAN which had whip antenna similar to radio but is now obsolete.

I pulled it as tight as I could and used a white pencil to mark where the snaps go. I did one snap at a time and with that one snapped I marked the spot for the next one. I would pull it as tight as you can because it tends to stretch some over time and wet weather.

EASY. I USED A SCRIBE (ICE PICK) TYPE DEVICE TO PUNCH HOLE, PLACE SNAP INTO HOLE, PLACE BACK OF SNAP ON IT AND MASH END WITH SNAP TOOL, AVAILABE AS A PLIER TYPE OR PUNCH WITH CUP TYPE AVAILABLE AT MARINE OR FABRIC STORE FOR VERY REASONABLE PRICE. :)

Edit postReport this postReply with quote Snap in console cover for 208 by Grady Again » May Thu 06, 2010 2:10 pm I HAVE A 97 208 ADVENTURE ALSO AND ORDERED A HELM COVER FROM A&J CANVAS 2453 STREETS FERRY ROAD VANCEBORO, NC 28586 252-244-1509 THEY HAD THE PATTERN AND THE ORIGINAL GRADY...

I have Costa Del Mar with the grey lens and do not have a problem reading LCD screens unless I turn my head sideways so that the glasses are vertical and not horizontal. I think this is the case with any polarized sunglasses. 8)

Just sent the e-mail. Very easy to do and only takes a minute. I've had enough problems in small motors and outboards with E-10, I can't imagine how bad E-15 is going to be.

I also contacted GW Customer Service for the same information on my 208 and they were quick to respond and told me exactly what I needed to know. I ordered a new sending unit form WEMAUSA and couldn't be happier. :D

Snap in console cover for 208 I HAVE A 97 208 ADVENTURE ALSO AND ORDERED A HELM COVER FROM A&J CANVAS 2453 STREETS FERRY ROAD VANCEBORO, NC 28586 252-244-1509 THEY HAD THE PATTERN AND THE ORIGINAL GRADY BLUE COLOR. THEY SENT THE SNAPS WITH IT AND I HAD TO PUT THEM ON AS SNAP...

I PUT A TEE IN LINE JUST BEFORE RECESSED FAUCET AND HOOKED A KITCHEN SINK SPRAYER INTO IT. ITS ENOUGH TO RINSE OFF WITH AND SPRAYER HAS A LEVER TO ACTIVATE IT.

Sorry, I don't know about the frame, I just copied the info from a previous post. Might give them a call.

Try this-copied from previous post. Suppose to be original mfgr. for GW The supplier is A and J Canvas - here is their contact information 2453 Streets Ferry Rd Vanceboro, NC , 28586-8350 Phone: 252-244-1509 FAX: 252-244-2508 A and J was great - they even still had the original...

Cleaning non skid gelcoat I use Mr. Clean Magic Erasers to clean. You will not believe how easy it is to do and how good a job it does. :lol:

Yamaha Dealer-Eastern Shore, md. Gootee's Marine in Golden Hill, Md (South of Cambridge, Md). See their web site for additional information. Best in this area. :)

New enclosuree on 204c I recently ordered a helm cover for my '97, 208 after reading the original post of saltydog. I agree that A & J Canvas was great. They had the pattern in stock and I had it within two weeks of ordering. Quality job for $150 and $50 shipping. I will not hesitate to use...

Cooler mat I use rubber shelf liner from Walmart-housewares section, works great-no skidding and protects deck. 8)

I have a '97 208 with fresh water tank. Gas cap look alike on side of stern port is for filling. Hose connection on front is for raw water washdown hose. My fresh water spigot (swing out faucet and on knob) :) is mounted in port gunwale under cap.

Dash looks great. Ineed to do something to the '97 208 I just purchased. Original is cracked around the screw holes. Where did you get the carbon fiber and was it easy to work with (cut,, drill, etc.). I've noticed a lot of custom cars are using CF. Thanks :D