Search results

I have a 2004 282 Sailfish with the 150 gallon main tank and the 70 gallon auxiliary tank. I need sending units for both. I am not near the boat right now. What have you all replaced them with? Part numbers and sources would be appreciated. Need to order soon.

If you have added underwater lights to the transom of an 04 282 Sailfish, I'd be interested in photos showing where you put them, even better, some measurements.

Anybody ever changed the LED lights out in the OEM switches? My nice blue lens NewWire rocker covers light up green instead of blue because the LEDs are amber... P/N for replacement LEDs would help...

2004 282 Sailfish: The rear bilge pump discharge hose seems stiff and brittle, so going to replace it while I have the pump out... I am contemplating replacing the hoses on both the foreward bilge pump and the shower sump. Has anyone done this? Any photos or sketches on how they are routed...

I need to replace the stern bilge pump and switch in my 04 282 Sailfish. I know how to wire it up. The problem is, I cannot physically reach the pump and switch! What is the trick?

I hate when I cannot find what I need for my 04 282 Sailfish... This fitting that the wiper arm hose connects to is broken off. Does anybody have any idea for a part number, hyperlink, or anything to find a replacement, or even a suitable substitute?

Some Grady Whites doing Grady White stuff.

Can anybody identify this transducer? I need to find a new bracket. This one had a rather unfortunate interaction with the First Mate's buffer... It came with a Raymarine Dragonfly 7. Any help would be appreciated.

Anybody know where I can get 1/16" thick Starboard near Richmond, Hampton Roads, or online? I also need some boards to make new toe boards...

I replaced my Bang Cap with 1/16" Stainless while I had the motors off. The brackets did mash down against the old aluminum Bang Cap,and there was some corrosion but not really bad. I dry fitted the brackets before caulking, and the gap is noticable. I haven't cranked the bolts hard yet, just...

Dunno if this is how y'all do it, but I looked at another wire going through the transom and didn't trust its seal integrity. For a new install, I hated drilling that huge hole to feed the transducer connector through. So, I slit a piece of fuel hose, waxed it, put it on the 'ducer wire, then...

2004 GW 282 Sailfish; going to start putting things back together, finally! Is there a torque specification for the bolts mounting the bracket to the transom, or do you crank on them until you can't get any more? My bottom bolts are 'stuck' in the transom. They are not coming out without some...

I'm looking for a Yamaha Dealer/Mechanic that also has Machine Shop/Welding capabilities... I am in Prince George County, VA, but power heads are off the boat so I am fairly mobile; looking for recommendations anywhere between Richmond, Hampton Roads, Norfolk, VA Beach area. Need to have...

This keeps getting better and better... Started off doing annual service. Found water in both gear cases, so pulled lowers to do seals & pressure tests, water pumps, etc. Scoped, discovered corrosion & ordered center section exhaust kits. Scope sucks, so couldn't really see block condition...

...I lost my photos of how the old ones were wired up due to a phone crash! I took the motors out and taped the wiring up 2 years ago, and had no memory of which wires connected to which posts... The first photo is the port side wires, 2nd photo is the new motor for the port side. The top tab...

Any tricks to pulling Yamaha Prop Shaft Housings *edited without buying the specific special tools? 04 F225s. I have some basic pullers and such, but haven't figured out how I'm going to get them out. Should I pull them before dropping the lower units?

##Edited## Some eagle eyes can read the decal, it appears to be a 248? I can blow it up enough to read it... My Father-inLaw really liked my Grady, and right before he passed he bought a 97 265, or that is what his text to me said. I haven't made it down to FL to survey the boat yet, and I...

04 282 Sailfish: Is this where you hook up the "drain" ground for a new transducer/bottom machine? First time seeing something with a "drain" wire.

So, the port 12V outlet is dead on my 2004 282 Sailfish. I checked every fuse and reset every breaker. I have no idea how the wires are routed. Ideas? The gauge is just on there temporarily to test for current.

I have searched and cannot find what I need... My Port Wiper Motor is out on my 2004 GW 282 Sailfish, and I need a replacement. They all seem to be shaped the same, but I need to be sure of the wipe pattern, park, etc. The part number on the sticker is WWF-12C16-1020. The owner's manual...